SYMPOSIA: |
AEROSPACE ENGINEERING |
AUTOMOTIVE ENGINEERING |
BIOENGINEERING |
COMBUSTION AND ENVIRONMENT ENGINEERING |
DYNAMICS, SOLID MECHANICS AND OPTIMIZATION |
ENERGY AND TRANSPORT PHENOMENA |
ENGINEERING EDUCATION |
MANUFACTURING PROCESSES |
MATERIALS SCIENCE AND ENGINEERING |
MECHATRONICS |
OFFSHORE & PETROLEUM ENGINEERING |
|
AEROSPACE ENGINEERING |
5N THRUSTER THERMO-ELASTIC ANALYSIS |
A DAMAGE MECHANICS BASED FAILURE MODEL FOR DYNAMIC IMPACT ON COMPOSITE LAMINATES |
A HYBRID INVERSE AERODYNAMIC DESIGN USING A VARIABLE METRIC OPTIMIZATION ALGORITHM |
A MONTE CARLO COMPUTATION OF THE FIRING ENVELOPE OF A VISUALLY GUIDED MISSILE: INTEGRATED GUIDANCE, CONTROL AND IMAGE PROCESSING ALGORITHMS |
A NEW CORRECTION METHOD FOR UNSTEADY PRESSURE COMPUTATIONS AND TRANSONIC AEROELASTIC STABILITY ANALYSES |
A PLANAR DOUBLET-LATTICE CODE FOR
TEACHING AND RESEARCH IN AEROELASTICITY |
A PROJECT FOR A NAVIGATION AND TELEMETRICS SYSTEM FOR UNMANNED AERIAL VEHICLES |
A REVIEW OF THE CHARACTERISTICS OF SUBMERGED AIR INTAKES |
A ROBUST WEIGHTED-BY-AREA INTERPOLATION METHOD FOR 3D FLUID-STRUCTURE INTERACTION |
A SIMPLE EXPERIMENTAL DEMONSTRATION OF AEROELASTIC INSTABILITIES |
A VERIFICATION TEST OF A DIRECT NUMERICAL SIMULATION CODE THAT USES A HIGH ORDER DISCRETIZATION SCHEME |
ACTIVE AEROELASTIC CONTROL OF VARIABLE CAMBER AIRFOIL IN THE PRESENCE OF STRUCTURAL NONLINEARITIES |
ADVANCED CFD ANALYSIS OF 14-BIS AIRCRAFT |
AERODYNAMIC HEATING ON VSB-30 SOUNDING ROCKET |
AEROTHERMODYNAMIC PERFORMANCE COMPARISON OF ROUND AND FLAT-NOSE LEADING EDGES AT HYPERSONIC FLIGHT SPEED |
AIRCRAFT PARAMETER ESTIMATION USING ADAPTIVE FUNCTIONAL LINK NETWORK |
AN APPLICATION OF A BOUNDARY INTEGRAL METHOD FOR SIMULATING POTENTIAL FLOW AROUND THREE-DIMENSIONAL BODIES
|
AN ENVIRONMENT FOR TESTING AND SIMULATING ALGORITHMS FOR AUTONOMOUS STAR SENSORS |
AN EXPERIMENTAL STUDY ON VIBRATION FREQUENCIES AND DAMPING PARAMETERS OF NANOCOMPOSITE PLATES |
AN H ADAPTIVE HIERARCHICAL PANEL METHOD FOR SOLVING A BIDIMENSIONAL POTENTIAL SUBSONIC FLOW |
AN INTERPLANETARY MISSION TO NEPTUNE SYSTEM: ON THE DYNAMICS OF
THE NEPTUNE SYSTEM ORBITER
|
ANALYSES OF NAVIGATIONAL ALGORITHMS FOR A REAL TIME DIFFERENTIAL GPS SYSTEM |
ANALYSING THE PERFORMANCE OF AN AEROSPACIAL VEHICLE CONTROLLER CONSIDERING UNCERTAINTIES AT THE STATES |
ANALYSIS OF CONVERGENCE ACCELERATION TECHNIQUES USED IN UNSTRUCTURED ALGORITHMS IN THE SOLUTION OF AERONAUTICAL PROBLEMS - PART I |
ANALYSIS OF ELECTRONIC PACKAGE COOLING IN AN AIRCRAFT USING CFD |
ANALYSIS OF THE AERODYNAMICS CHARACTERISTICS OF A WING-CANARD CONFIGURATION WITH CANARD DEFLECTION, USING PANEL METHOD |
ANALYSIS OF THE FLOW IN LIQUID PROPELLANT ENGINE SWIRL INJECTORS USING CFD |
ANALYSIS OF THE IMPACT OF FLOW BOUNDARY CONDITIONS ON THE PERFORMANCE OF A LEAN-PREMIXING COMBUSTOR MODEL |
ASSESSMENT OF TRANSITION MODELS FOR AERODYNAMIC APPLICATIONS |
AUTOMATION SYSTEM FOR ROCKET MOTORS ANOMALIES DETECTION THROUGH TOMOGRAPHIC IMAGES - AN INITIAL PROPOSAL |
CHAOS PREDICTION OF STALL-INDUCED OSCILLATIONS VIA LYAPUNOV EXPONENTS |
CHARACTERIZATION OF THE EXPERIMENTAL OPERATION, IN THE ATMOSPHERE AND VACUUM, OF A SMALL PLASMA TORCH, DEVELOPED FOR THERMAL PROTECTION MATERIALS TEST. |
CLOSE APPROACH TO NEPTUNE USING GRAVITY ASSISTS |
COMPARISON BETWEEN A CENTERED AND A HIGH RESOLUTION UPWIND SCHEMES IN THE SOLUTION OF AEROSPACE PROBLEMS USING UNSTRUCTURED STRATEGY |
COMPARISON BETWEEN CONVENTIONAL FLIGHT TEST MANEUVERS FOR AIRCRAFT AERODYNAMIC DERIVATIVES ESTIMATION |
COMPARISON BETWEEN MODERN PROCEDURES FOR
AERODYNAMIC CALCULATION OF SUBSONIC AIRFOILS FOR
APPLICATION IN LIGHT AIRCRAFT DESIGNS |
COMPARISON BETWEEN THE ELASTIC MODULUS OBTAINED BY TENSILE AND FREE VIBRATION EXPERIMENTS FOR GLARE MATERIAL |
COMPUTATIONAL SIMULATION OF AN AIRCRAFT CABIN PRESSURE CONTROL SYSTEM |
COMPUTER MODELS FOR TROPICAL AND MIDLATITUDE ATMOSPHERES |
CONSTRUCTION OF THIRD-ORDER ENO AND WENO FINITE VOLUME SCHEMES FOR GENERIC UNSTRUCTURED GRIDS |
CONVECTIVE FLUX SCHEMES FOR HIGH-REYNOLDS-NUMBER TURBULENT COMPRESSIBLE FLOWS |
COVARIANCE INTERSECTION-BASED SENSOR FUSION WITH LOCAL MULTIPLE MODEL HYPOTHESIS TESTING FOR SOUNDING ROCKET TRACKING AND IMPACT POINT PREDICTION |
CRACK GROWTH RETARDATION EFFECTS IN CIVIL AIRPLANE STRUCTURES |
DAMAGE TOLERANCE OF NANOCOMPOSITES UNDER IMPACT LOADINGS |
DEGRADATION OF CARBON-BASED MATERIALS DUE TO
IMPACT OF HIGH-ENERGY AIR PLASMA |
DESIGN AND FLIGHT TEST OF A PARAFFIN BASED HYBRID ROCKET |
DESIGN POINT EFFICIENCY OPTIMIZATION OF A MULTI-STAGE AXIAL-FLOW COMPRESSOR FOR AERO APPLICATION APPLYING A SPECIALLY DEVELOPED COMPUTER CODE |
DESIGN PROCEDURE FOR A FOWLER FLAP MECHANISM |
DETERMINATION OF THE OUTFLOW VALVE OPENING AREA OF THE AIRCRAFT CABIN PRESSURIZATION SYSTEM |
DETTACHED EDDY SIMULATION OF THE TRANSONIC FLOW OVER A CIRCULAR CYLINDER |
DEVELOPMENT AND ANALYSIS OF A GROUND IMPACT ATTENUATOR FOR THE RE-ENTRY SATELLITE SARA |
DEVELOPMENT OF A CODE FOR A DIRECT NUMERICAL SIMULATION OF COMPRESSIBLE SHEAR FLOW INSTABILITIES |
DEVELOPMENT OF A DATA ACQUISITION SYSTEM FOR LIGHT AIRPLANES FLIGHT TESTS |
DEVELOPMENT OF A METODOLOGY FOR 2-D HIGH LIFT TESTING USING A BOUNDARY LAYER CONTROL SYSTEM BY AIR BLOWING |
DYNAMIC ANALYSIS OF THE MULSTISTAGE PARACHUTE-STORE SYSTEM
|
DYNAMIC CHARACTERIZATION OF A LIQUID PROPELLED ROCKET COMBUSTION CHAMBER |
EFFECT OF THE HYGROTHERMAL CONDITIONING ON THE MECHANICAL PROPERTIES OF CARBON FIBER/EPOXY COMPOSITES |
EFFECTS OF A SYNTHETIC JET ACTUATOR ON THE DELAY OF SEPARATION IN A BOUNDARY LAYER |
ENERGY ABSORPTION CAPABILITY OF COMPOSITE TUBES UNDER COMPRESSION LOAD |
ENGINE AIRFRAME INTEGRATION STUDIES USING THE CFD++ CODE |
ESTIMATING THE FRETTING FATIGUE LIMIT BY FINITE ELEMENT ANALYSIS |
ESTIMATION OF TORQUE IN A REACTION WHEEL USING A BRISTLE MODEL FOR FRICTION |
EVALUATION OF A SIDEWALL BOUNDARY-LAYER CONTROL SYSTEM BY AIR BLOWING
|
EVALUATION OF AN ANALYTICAL MODEL FOR ADHESIVELY BONDED REPAIR IN COMPOSITE PLATES |
EVALUATION OF COMPRESSION AFTER IMPACT STRENGTH OF CARBON/EPOXY COMPOSITES USED IN AERONAUTICAL AREA
|
EXPERIMENTAL ANALYSIS OF THE AERODYNAMICS CHARACTERISTCS OF A TWO ELEMENT WING WITH CERRATED MAIN ELEMENT TRAILING EDGE |
EXTINCTION OF METHANE DIFFUSION FLAMES ENRICHED BY HYDROGEN |
FAULT DIAGNOSE IN THE AUTONOMY MICRO-SATELLITE ATTITUDE DETERMINATION USING GPS AND GYROS: SIMULATION RESULTS |
FIRST STEPS OF THE INFRARED SIMULATION DEVELOPMENT BY TUNGSTEN FILAMENT LAMPS |
FLIGHT PATH OPTIMIZATION FOR COMPETITION SAILPLANES THROUGH STATE VARIABLES PARAMETERIZATION |
FLIGHT PATH RECONSTRUCTION USING THE UNSCENTED KALMAN FILTER ALGORITHM |
FLIGHT TEST MANEUVERS OPTIMIZATION FOR PARAMETER IDENTIFICATION |
FLIGHT TESTS FOR PARAMETER INDENTIFICATION IN LIGHT AIRPLANES |
FLOW CASCADE ANALYSIS EMPLOYING HESS & SMITH MODIFIED PANEL METHOD AND A CDF CODE |
FREQUENCY DOMAIN AERODYNAMIC RESPONSES FOR AEROELASTIC ANALYSES IN THE UNSTEADY TRANSONIC REGIME |
GAS TURBINE IDENTIFICATION WITH LINEAR AND NON-LINEAR TECHNIQUES |
GAS-SURFACE INTERACTION IMPACT ON AERODYNAMIC SURFACE QUANTITIES OF LOW-DENSITY HYPERSONIC FLOW OVER FLAT-NOSE BODIES |
GAS-SURFACE INTERACTION IMPACT ON FLOWFIELD STRUCTURE OF LOW-DENSITY HYPERSONIC FLOW OVER FLAT-NOSE BODIES |
GAS-SURFACE INTERACTION IMPACT ON SHOCK WAVE STRUCTURE OF LOW-DENSITY HYPERSONIC FLOW OVER FLAT-NOSE BODIES |
GENETIC APPROACH ON LQWEIGHTING MATRICES SELECTION AND ITS APPLICATION IN THE VLS ATTITUDE CONTROL |
GRAVITATIONAL CAPTURE OF A SATELLITE BY THE MAJOR PRIMARY |
HIGH SPEED FLOW OVER A FLAT PLATE AND ON A STEP OBSTACLE |
IDENTIFICATION OF THE AERODYNAMIC AND CONTROL DERIVATIVES AND FLIGHT PATH RECONSTRUCTION OF THE SZD-50-3 PUCHAZ SAILPLANE |
IMPLEMENTATION AND EVALUATION OF RANS TURBULENCE MODELS IN THE BRU3D CODE |
IMPLEMENTATION OF A POSITIONING SYSTEM BASED ON INS/GPS INTEGRATION |
INDICIAL RESPONSE OF THIN WINGS IN A COMPRESSIBLE SUBSONIC FLOW. |
INVESTIGATION OF MICROSCOPIC DEFECTS IN AIRCRAFT WINGS WITH THE HELP OF VIRTUAL TOOLS
|
INVESTIGATION OF THE PERFORMANCE OF A 200 N SATTELITE THRUSTER OPERATING IN DIFFERENT ALTITUDES |
LOAD SPECTRUM EVALUATION FOR FAB T-25 DTA PROGRAM |
LOW-COST ALTERNATIVE PATHS FOR DIRECT EARTH-MOON TRANSFER |
METHOD FOR GLOBAL AND LOCAL LEAK DETECTION APPLICATION FOR HYDRAZINE PROPULSION SYSTEMS |
METRICS CONVERSION IN AIRPORT NOISE |
MODELING OF A CALIBRATION CURVE OF AN EXTERNAL AERODYNAMIC BALANCE USING MULTILAYER PERCEPTRON ARTIFICIAL NEURAL NETWORKS |
MULTI-CRITERIA DESIGN OF AIRCRAFT CONTROL SYSTEMS USING A-TEAMS |
MULTI-OBJECTIVE OPTIMIZATION APPLIED TO A SATELLITE CONSTELLATION CONSIDERING UNCERTAINTIES IN THE POSITION MEASURES AND ERRORS IN THE ORBITAL MANEUVERS |
MULTI-POINT ALGORITHM FOR INVERSE AERODYNAMIC DESIGN |
NONLINEAR PHENOMENA IN COMPUTATIONAL TRANSONIC AEROELASTICITY |
NOVEL LOOP HEAT PIPES DEVELOPMENT FOR GROUND AND SPACE APPLICATIONS |
NUMERICAL ANALYSIS AND EXPERIMENTAL SHOCK MEASUREMENTS
ON A SATELLITE LAUNCHER INERTIAL SENSOR MODULE |
NUMERICAL CALCULATION OF THE USTEADY TWO-DIMENSIONAL INCOMPRESSIBLE FLOW AROUND NACA AIRFOILS USING THE VORTEX METHOD |
NUMERICAL EVALUATION OF THE FLOW INSIDE THE TRANSONIC NOZZLE OF A
DIRECT-CONNECT SUPERSONIC COMBUSTION RESEARCH FACILITY
|
NUMERICAL METHODS TO MANEUVER A SATELLITE USING A LOW THRUST ENGINE |
NUMERICAL SIMULATION OF FLOW AROUND A NACA 0012 AIRFOIL IN TRANSIENT PITCHING MOTION USING IMMERSED BOUNDARY METHOD WITH VIRTUAL PHYSICAL MODEL |
NUMERICAL SIMULATION OF HIGH REYNOLDS NUMBER FLOWS OVER CIRCULAR CYLINDERS USING THE IMMERSED BOUNDARY METHOD |
NUMERICAL SIMULATION OF THE TRANSONIC LAMINAR FLOW IN AIRFOILS WITH PITCHING AND PLUNGING MOTION |
NUMERICAL SIMULATION OF TURBULENCE IN OPEN-CHANNEL FLOWS |
NUMERICAL STUDY OF TWO-DIMENSIONAL HIGH-LIFT CONFIGURATIONS USING THE MSES CODE |
ON THE BEHAVIOR OF UPWIND SCHEMES APPLIED TO COLD GAS HYPERSONIC FLOWSIMULATIONS OF INLET CONFIGURATIONS |
ON THE DEVELOPMENT OF A 3-D MULTIGRID UNSTRUCTURED CODE FOR COMPLEX
AEROSPACE APPLICATIONS |
ON THE FATIGUE LIMIT FOR CYLINDRICAL CONTACTS UNDER A PARTIAL SLIP REGIME |
OPTIMIZATION OF AIRPLANE TAKEOFF PERFORMANCE |
OPTIMIZATION OF LOW-THRUST LIMITED-POWER TRANSFERS BETWEEN COPLANAR CIRCULAR ORBITS |
OVERVIEW ON NACELLE DESIGN |
OVERVIEW ON THRUST REVERSER DESIGN |
PARAMETRIC OPTIMIZATION OF INTEGRALLY MACHINED PANELS REGARDING FOUR STABILITY CRITERIA |
POST BUCKLING ANALYSIS OF COMPOSITE MATERIAL PLATES IN THE PRESENCE OF THERMAL RESIDUAL STRESSES |
PROJECT OF A MODEL FOLLOWING FLIGHT CONTROL SYSTEM OF A VARIABLE STABILITY AIRCRAFT |
PROPOSAL OF A TRADE OFF DECISION SUPPORT SYSTEM THROUGH INTEGRATIVE PARAMETERS FOR SATELLITE DESIGN PROCESS |
QUASI-STEADY DROPLET COMBUSTION WITH FUEL LEAKAGE |
REAL-TIME IMPLEMENTATION OF A LOW COST INS/GPS KALMAN FILTER BASED NAVIGATION SYSTEM |
REGRESSION RATE STUDIES OF A PARAFFIN-BASED HYBRID ROCKET |
SECONDARY KELVIN-HELMHOLTZ INSTABILITY IN A STABLY STRATIFIED MIXING LAYER |
SIMULATION AND IDENTIFICATION OF A FLIGHT ENVELOPE USING NEURAL NETWORKS |
SIMULATION OF GUST RESPONSE OF COMMERCIAL AIRCRAFT USING THE PEELE METHOD |
SIMULATION OF ROUND LEADING EDGE AEROTHERMODYNAMICS |
SOFTWARE DEVELOPMENT AND VALIDATION FOR SUBSONIC AND TRANSONIC AIRCRAFT CLASS 2 DRAG POLAR DETERMINATION |
SOLUTION OF THE EULER EQUATIONS IN THE THREE-DIMENSIONAL SPACE USING THE MACCORMACK ALGORITHM - PART I |
SOLUTION OF THE EULER EQUATIONS IN THREE-DIMENSIONS USING THE JAMESON AND MAVRIPLIS ALGORITHM - PART I
|
SOLUTION OF THE NAVIER-STOKES EQUATIONS IN THE THREE-DIMENSIONAL SPACE USING THE MACCORMACK ALGORITHM - PARTE II |
SOLUTION OF THE NAVIER-STOKES EQUATIONS IN THREE-DIMENSIONS USING THE
JAMESON AND MAVRIPLIS ALGORITHM - PART II
|
STABILITY PREDICTION AND HANDLING QUALITIES ANALYSIS OF HYPERSONIC FLIGHT VEHICLES DURING ACCELERATION |
STUDIES ON THE CONVERGENT-DIVERGENT NOZZLES FOR SIMULATION OF REENTRY AERODYNAMIC FLOWS ON THE PLASMA SYSTEM OF THE LABORATÓRIO DE PLASMAS E PROCESSOS OF THE INSTITUTO TECNOLÓGICO DE AERONÁUTICA (LPP-ITA) |
STUDY OF THE AIR BLEED INFLUENCE IN THE INDUSTRIAL GAS TURBINE PERFORMANCE |
STUDY OF THE HYGROTHERMAL EFFECTS ON THE COMPRESSION STRENGTH OF CARBON TAPE/EPOXY COMPOSITES
|
THE DETERMINATION OF THE VELOCITIES AFTER IMPACT FOR THE CONSTRAINED BAR PROBLEM
|
THE SPECIFICATION FOR THE QUALIFICATION OF THE AFT COVER FIXATION SCREW OF THE SATELLITES LAUNCH VEHICLE VLS-1 ENGINES |
THEORY OF INVENTIVE PROBLEM SOLVING APPLIED TO BUSINESS PROCESS MANAGEMENT PROJECTS (BPM-TRIZ) |
TIME DOMAIN IDENTIFICATION OF LOW ORDER EQUIVALENT SYSTEM FROM FLIGHT DATA |
TOPOLOGY OPTIMIZATION FOR FLEXIBLE STRUCTURES
|
TRANSIENT PERFORMANCE OF GAS TURBINES. |
UNSTEADY COMPRESSIBLE AERODYNAMICS CAUSED BY VERTICAL GUSTS AND VORTICES |
USING SINGULAR AND NON-SINGULAR ELEMENTS AND BEM AND FEM STRATEGIES FOR THE COMPUTATION OF K-I IN LEFM |
VISCOUS-INVISCID INTERATION FOR THE SOLUTION OF THE FLOW ABOUT AIRFOILS |
VOLUMETRIC MESH MOVEMENT GUIDED BY GEOMETRIC INFORMATION |
WELDING HEAD DEVELOPMENT AND QUALIFICATION
FOR SOLAR ARRAY MANUFACTURING FOR SPACE APPLICATIONS
|
WHICH IS THE BEST HELICOPTER? |
WIND TUNNEL TEST OF A THREE-ELEMENT AIRFOIL CONFIGURATION: INFLUENCE OF THE DIRECTION AND THE DISTANCE OF A BLOWER USED TO MINIMIZE THREE-DIMENSIONAL FLOW ALONG THE MODEL SPAN |
WINGS CONSTRUCTION USING A FOAM CNC CUTTER |
|
top |
|
AUTOMOTIVE ENGINEERING |
A METHODOLOGY PROPOSAL FOR A REAL DRIVING CITY CYCLE IMPLEMENTATION IN CHASSIS DYNAMOMETER FOR EMISSION TESTS |
A PIECEWISE NONLINEAR CONTROL APPLIED TO VEHICULAR DYNAMICS. |
A STUDY OF NON-TRADITIONAL GEOMETRIES AND ALTERNATIVE ALLOYS FOR NGV STORAGE GAS TANKS |
AIR/FUEL MIXTURE FORMATION IN TURBOCHARGED SPARK-IGNITION ENGINES: EFFORTS TOWARDS MITIGATION OF POLLUTANT FORMATION |
AN ALTERNATIVE APPROACH FOR THE TREATMENT OF THE DYNAMICS OF GROUND VEHICLES ON SUSPENSION. |
AN ALTERNATIVE HYBRID AUTOMOTIVE POWERTRAIN SYSTEM |
AN EDUCATIONAL TOOL TO STUDY THE VEHICLE DYNAMIC RESPONSE DURING RIDE ANALYSIS |
ANALYSIS OF AN OTTO CICLE ENGINE PERFORMANCE REGARDING TO ALCOHOL CONCENTRATION IN GASOLINE AND CNG USAGE |
ANALYSIS OF THE LATERAL STABILITY OF CARGO VEHICLES COMBINATIONS - CVCS. |
ANALYSIS OF THE PERFORMANCE OF A POROUS FOAM SOOT REGENERATIVE FILTER FOR DIESEL ENGINES |
ANTI-LOCK BRAKING SYSTEM MODEL |
APPLICATION OF THE TWO-LOAD METHOD ON THE EVALUATION OF THE ACOUSTICAL EFFICIENCY OF HELMHOLTZ RESONATORS |
AUTOMOTIVE ELECTRONICS IN BRAZIL: FACTS, TRENDS AND PROPOSALS. |
COMPARISON OF SIMULATION METHODOLOGIES FOR SUCTION AND DISCHARGE SYSTEMS |
COMPRESSION-IGNITION ENGINE MODELING |
COMPUTACIONAL SIMULATION OF THE EXHAUST GASES FLOW THROUGH A PLATINUM/PALADIUM CATALYTIC CONVERTER |
COMPUTATIONAL ANALYSIS OF THE AIR FLOW AROUND A COMMERCIAL BUS MODEL |
COMPUTATIONAL BLOCK-DIAGRAM EXECUTION OF MULTIPORT FIELDS
MODELS WITH CAUSAL CONSIDERATIONS |
CONVERSION METHODOLOGY OF AN AUTOMOTIVE ENGINE INTO AN AERONAUTICAL ENGINE |
DAMPING CONTROL IN HYDROPNEUMATIC SUSPENSION |
DYNAMICAL PERFORMANCE OF A BUS UNDER DIRECTIONAL MANEUVER |
ENGINES CAMSHAFT EVALUATION REGARDING TAPPETS ROTATION |
FLEXIBLE VEHICLE MODEL FOR PLANAR COLLISIONS ANALYSIS |
FOUR-WHEEL VEHICLE SUSPENSION MODELING FOR CONTROL SYSTEM DEVELOPMENT |
GASOLINE "A" AND HYDRATED ETHANOL BLENDS: EXPERIMENTAL ANALYSIS ON THE VIABILILITY OF UTILIZATION IN A CYCLE OTTO ENGINE
|
IMPLEMENTATION AND TESTS OF A VARIABLE CONTROL SYSTEM OF SPARK TIME IGNITION AND INJECTION TIME, USING DIGITAL SIGNAL PROCESSOR - DSP. |
INFLUENCE OF FRICTION MODIFIER ADDITIVES ON THE TRIBOLOGY OF LUBRICATING OILS |
INFLUENCE OF SHIELDING GAS MIXTURES ON WELDING PROCESS OF
GALVANIZED SHEET |
LIGHT DUTY VEHICLES EXHAUST EMISSION EVALUATION FOLLOWING BRAZILIAN AND ARGENTINEAN LEGISLATIONS |
METALLIC PARTICLE DETECTION IN LUBRICANT OIL USING IMAGE PROCESSING |
MODELING OF A VEHICLE SUSPENSION WITH NON LINEAR ELEMENTS AND PERFORMANCE COMPARISON TO A SEMI-ACTIVE MODEL |
OPACITY EMISSION INSPECTION FROM THE EXHAUST PIPE ON DUTY VEHICLES IN BELO HORIZONTE, MINAS GERAIS, BRAZIL. |
PERFORMANCE ANALYSIS OF AN CNG-FUELLED FLEX ENGINE TO DIFFERENT COMPRESSION RATIOS |
PERFORMANCE OPTIMIZATION OF A MULTI-FUEL SPARK IGNITION ENGINE |
PNEUMATIC REGENERATIVE BRAKE EQUIPPED WITH ABS |
PNEUMATIC REGENERATIVE BRAKE SYSTEM |
PROJECT AND ADAPTATION OF TORCH IGNITION SYSTEM IN AN OTTO CYCLE ENGINE |
PROJECT OF EMBARKED SYSTEM OF INSTRUMENTATION TO MONITORING THE PERFORMANCE OF THE URBAN BUS ENGINE USE GNV FUEL. |
RADIAL TURBO-COMPRESSOR MODELING |
STRUCTURAL DYNAMICS OF THE CHASSIS OF A LIGHT TRAILER |
THE CALIBRATION AND ADJUSTMENT METHODOLOGY APPLIED TO GENERAL ENGINE MANAGEMENT SYSTEM FOR SPARK IGNITION TURBO ENGINES |
THE IMPLEMENTATION OF AN EDUCATIONAL ODS TOOL USED TO VERIFY DYNAMIC VEHICULAR RESPONSES |
THE MULTI-BODY MODELING AS A DEVELOPMENT TOOL IN VEHICULAR PROJECTS |
THE THERMOELASTIC TECHNIQUES FOR THE MEASUREMENT OF STRESSES DISTRIBUTION ON COMPONENT OF STRUCTURES OR MACHINES |
THE USE OF PALM OIL IN DIESEL ENGINE |
TWO DIMENSIONAL ANALYSIS OF PRECISION INSERT BEARING INTERFERENCE FIT |
VIRTUAL PROTOTYPING : A VEHICLE MODEL FOR INTEGRATED MOTION CONTROL STUDIES |
|
top |
|
BIOENGINEERING |
A BLACK-BOX BACK-PROJECTION ALGORITHM FOR ELECTRICAL IMPEDANCE TOMOGRAPHY |
A NUMERICAL COMPARISON BETWEEN AXISYMMETRIC AND 2-D FINITE VOLUME FORMULATIONS USED IN THE THERMAL ANALYSIS OF OCULAR TISSUES |
A SINGLE DOF HAPTIC INTERFACE FOR COMPUTER INTERACTION |
ADHESION AND MORPHOLOGY OF FIBROBLASTIC CELLS CULTURED ON DIAMOND-LIKE CARBON (DLC)-COATED AND UNCOATED TI-13NB-13ZR |
AIR FLOW AND THERMAL STATE IN LARGE AERATED GRAIN STORAGE |
ANALYSIS OF STRESS PRODUCED BY SPLINTED IMPLANTS WITH SOLDERED BAR |
ANALYSIS OF THE INCOMING FLOW IN A BLOOD FILTER |
ANALYSIS OF WEAR OF THE ACETABULAR COMPONENT OF TOTAL HIP PROSTHESIS: EFFECTS OF MATERIAL AND ORIENTATION |
ANTROPOMETRIC-ANTROPOMORFIC 3D VOXEL MODEL REPRESENTATIVE OF A THORAX'S RABBIT FOR DOSIMETRIC PROPOSALS |
ASSESSMENT OF THE EFFECT OF THE IONIC IMPLANTATION BY PLASMA IMMERSION ON THE FLEXIBILITY OF THE NICKEL-TITANIUM ENDODONTIC FILES |
AUTOMATIZATED PROCESSING FOR PHOTOELASTIC PARAMETERS. |
AUXILIARY TOTAL ARTIFICIAL HEART MONITORING OPERATION IN LABVIEW® |
BIOMECHANICAL MODEL FOR NET JOINT TORQUES ESTIMATION IN PEDALING |
BIOMECHANICAL STUDY OF VOLAR PLATE LESIONS IN THE FINGERS INTERPHALANGEAL JOINTS |
BLOOD FLOW NUMERICAL SIMULATION OF AN IDEALISED STENOSED ARTERY: FINITE ELEMENT METHOD AND FINITE VOLUME METHOD COMPARISON |
CHARACTERISTIC CURVES OF PNEUMATIC MUSCLE FOR THE USE IN THE UFMG EXOESKELETON |
COMPARISON BETWEEN MALE AND FEMALE GAIT MODES PART I: KINEMATICS OF THE ANKLE, KNEE AND HIP JOINTS |
COMPUTATIONAL BLOOD FLOW BEHAVIOUR FOR TWO RHEOLOGICAL MODELS |
DEPOSITION AND CHARACTERISTICS OF HARD AMORPHOUS FILMS ON BIOMEDICAL POLYETHYLENE AND METALLIC SUBSTRATES |
DESIGN OF A THREE-AXIAL TRANSDUCER OF FORCE AND MOMENT FOR AMPUTEE GAIT ANALYSIS |
DETERMINATION OF THE INLET PORT`S ANGLE FOR A CENTRIFUGAL BLOOD PUMP BY THE HYDRODYNAMIC CHARACTERISTICS |
DEVELOPMENT OF A DEVICE AND AN EXPERIMENTAL PROTOCOL TO PRODUCE THROMBI IN VITRO. |
DEVELOPMENT OF A FUNCTIONAL HAND ORTHOSIS |
DEVELOPMENT OF A HIP ORTHOSIS USING PNEUMATIC ARTIFICIAL MUSCLES TO CONTROL THE JOINT ROTATION |
DEVELOPMENT OF A SOFTWARE FOR THE PLANTAR FOOT PRESSURE MEASUREMENT |
DEVELOPMENT OF THE AGGREGOMETER FOR NEAR-INFRARED SENSORS THAT STUDY OF THE PLATELET AGGREGATION |
DEVELOPMENT OF THE JOINT POSITION SYSTEM FOR CONTROLLING THE EXOSKELETON BASED ON PNEUMATIC MUSCLES |
DEVELOPMENT OF TI-13NB-13ZR IMPLANTS BY POWDER METALLURGY |
DEVELOPMENT, INSTRUMENTATION AND STANDARDIZATION OF THE EQUIPMENT FOR MODIFIED THOMAS TEST |
DRAG REDUCTION IN VASCULAR SYSTEMS |
DYNAMIC TESTINGS ANALYSIS OF ARTERIAL BLOOD FILTERS |
EAP ACTUATORS FOR MICRO ROBOTICS: A NEW PERSPECTIVE |
EFFECT OF INORGANIC FILLER ON THE MECHANICAL AND TRIBOLOGICAL PERFORMANCE OF COMPOSITE MATERIALS |
EFFECT OF INTRA-RADICULAR POSTS FOR STRESS DISTRIBUTION IN RADICULAR DENTIN |
EFFECTS INDUCED BY INITIAL CHITOSAN SOLUTION CONCENTRATION AND CHITIN AND GLYCEROL INCORPORATION ON THE CHARACTERISTICS OF DENSE CHITOSAN MEMBRANES WITH POTENTIAL USE AS BURN DRESSINGS |
ELECTRICAL CAPACITANCE METHOD APPLIED TO THE STUDY OF ACUTE EDEMAS |
ELECTRO-FLUID-DYNAMIC SIMULATOR OF THE CARDIOVASCULAR SYSTEM FOR THE RESEARCH IN ASSISTED CIRCULATION AREA |
ESTIMATION OF HEAT TRANSFER COEFFICIENT OF CRYOGENIC SPRAY COOLING |
EVALUATION OF INTRAMUSCULAR TISSUE RESPONSE TO ZIRCONIA-HYDROXYAPATITE (ZH) CERAMIC IMPLANTS IN DOGS.
|
EVALUATION OF THE EXTERNAL HEXAGON DENTAL IMPLANTS AFTER SIMULATING SURGICAL PLACEMENT AND THE ROTATIONAL FREEDOM OF IMPLANT COMPONENTS |
EXPERIMENTAL ANALYSIS OF ORTHODONTICS ELASTICS UNDER PRE STRESSED LOADING |
EXPERIMENTAL ANALYSIS ON THE FASTENING OF COMPONENTES OF AN IMPLANT-SUPPORTED DENTAL PROSTHESIS |
EXPERIMENTAL STUDY OF THE ESCHERICHIA COLI RETENTION MAKING USE OF CROSSFLOW MICROFILTRATION WITH DIFFERENT MICRO-POROUS STRUCTURES |
IN VITRO ANALYSIS OF ORTHODONTICS ELASTICS IN ACID AND IN BASIC ACQUOUS SOLUTIONS |
INFLUENCE OF LYOPHILIZATION, STERILIZATION AND REHYDRATION ON THE MECHANICAL PROPERTIES OF BOVINE CORTICAL BONE |
INFLUENCE OF ORIFICE DEPTH AND PREPARATION ON THE INSERTION TORQUE AND PULLOUT STRENGTH OF PEDICULAR SCREWS |
INFLUENCE OF ORIFICE DEPTH AND PREPARATION ON THE INSERTION TORQUE AND PULLOUT STRENGTH OF PEDICULAR SCREWS |
INFLUENCE OF THE GEOMETRIC SHAPE OF PROSTHESIS ON THE STRESS DISTRIBUTION IN THE DENTAL IMPLANTS |
INFLUENCES OF THE FORCE OF PROPULSION WHEELCHAIR STANDARD OVER THE WHEELCHAIR VELOCITY |
MEASUREMENT OF THE MEDIAL PLANTAR ARCH USING SHADOW MOIRÉ |
MECHANICAL AND METALLURGICAL EVALUATION TO VALIDATION OF ASTM F136 6AL- 4V ORTHESIS´S FORMING MANUFACTURING FOR SURGICAL IMPLANTS |
MECHANICAL PROPERTIES CHARACTERIZATION OF KNEE CRUCIATE LIGAMENTS THROUGH TENSILE TESTS |
MECHANICAL PROPERTIES OF TI-13NB-13ZR ALLOY COLD WORKED BY SWAGING AND ROLLING |
MECHANICAL PROPERTIES OF VERTEBRAL FIXATION USING AN INTERNAL FIXATOR WITH THE PARTICIPATION OF THE GRAFT AND OF A LATERAL STABILIZER |
MECHATRONIC DESIGN METHOD FOR SURGERY DEVICES |
MECHATRONIC PUMP CHARACTERIZATION: THE "MECH-PUMP" |
MEDICAL PRODUCT DESIGN: EVOLUTION OR REVOLUTION? |
MODIFIED WEIGH FUNCTION IN BACKPROJECTION METHOD |
MODULATION OF CELL MOTOGENIC BEHAVIOUR USING BIOFABRICATION TECHNIQUES TO MIMIC THE EXTRACELLULAR MATRIX |
NEW ALGORITHM FOR CONVERTING A CSG REPRESENTATION INTO A B-REP REPRESENTATION |
OPTIMIZATION OF IMPLANTODONTIC SURGERY BY BIOMODELS OBTAINED VIA RAPID PROTOTYPING (RP): CASE STUDY |
PELVIC FLOOR MUSCLE SIMULATION FOR STRENGHT TESTS |
PODE DESIGN AND CONSTRUCTION OF A LOW COST FORCE FEEDBACK MANIPULATOR |
PREPARATION, CHARACTERIZATION AND SINTERING OF TI-35NB-7ZR-5TA ALLOY FOR BIOMEDICAL APPLICATIONS |
PROCESSING THE RAMAN SPECTRUM USING WAVELETS AND NEURAL NETWORK TO DIAGNOSE HUMAN BASAL CELL CARCINOMA |
PROJECT OF A MECHANICAL DEVICE TO EFFECT THE POSTURAL DRAINAGE |
SPATIOTEMPORAL DECOMPOSITION OF GAIT DATA TO ESTABLISH THE MAIN GAIT MODES THAT FORM THE FINAL WALKING KINEMATICS |
STIMULON: NEW METHOD AND DEVICE IN PHYSICAL THERAPY AND REHABILITATION. |
STRAIN DISTRIBUTION ON ORAL IMPLANTS WITH DIFFERENT DESIGNS OF CONNECTIONS |
STRESS/STRAIN FIELD ANALYSIS IN THE MANDIBULOTOMY TECHNIQUE USING THE FINITE ELEMENT METHOD |
STRUCTURAL ANALYSIS OF AN AUXILIARY TOTAL ARTIFICIAL HEART: TWO HYPOTHESES FOR THE LOSS OF RESISTANCE DURING "IN VIVO" ANIMAL TESTS |
STUDY OF PROJECTION MOIRÉ TECHNIQUE APPLIED ON FREE CONTOURS MEASUREMENT OF BIOENGINEERING |
STUDY OF THE NECESSARY MECHANICAL MODIFICATIONS FOR THE OPERATIONAL OPTIMIZATION OF THE SANTA CLARA DAM'S FISH LIFT |
SUCTION PRESSURE BEHAVIOR IN FUNCTION OF THE HOLES IN THE SUCTION DEVICES OF LUNG SECRETIONS |
THE USE OF SUPERVISORY SOFTWARE AS A OPTIMIZATION TOOL FOR CAN STERILIZATION PROCESSES |
THE USE OF ULTRASOUND AND MICROBUBBLES FOR THROMBUS FRAGMENTATION. |
THERMAL STRESS ANALYSIS FOR RESTORED AND SANE LOWER SECOND MOLAR |
TRIBOCHEMICAL TOOTH WEAR IN COLA BEVERAGES |
WEAR BEHAVIOUR IN ACETABULAR METAL-ON-METAL COMPONENTS - RETRIEVAL ANALYSIS |
|
top |
|
COMBUSTION AND ENVIRONMENT ENGINEERING |
A COMPARISON BETWEEN THERMOELETRIC POWER PLANTS OPERATIGN WITH NATURAL GAS AND DIESEL: ENVIRONMENT IMPACTS |
A KINETICS STUDY ON THE SORPTION OF SO2 BY LIMESTONE THROUGH THERMOGRAVIMETRY |
A NEW PERSPECTIVE ON DROPLET COMBUSTION IN LOW GRASHOF NUMBER REGIME |
A PROPOSAL OF FUZZY MULTIVARIABLE IDENTIFICATION FOR LIQUID INCINERATION NONLINEAR PROCESS COMBUSTION CONTROL |
A TURBULENT COMBUSTION MODEL BASED ON LARGE SCALE MOTION COUPLED TO PERFECTLY STIRRED REACTOR COMPARED TO A PARTIALLY STIRRED REACTOR |
ANALYSIS OF FLAME BEHAVIOUR IN SMALL COMBUSTION CHAMBERS USING CFD |
ANALYSIS OF THE THERMAL IGNITION AND INDUCTION TIME OF PREMIXED ETHANOL AND AIR COMBUSTION |
ANALYTICAL MODEL OF ATMOSPHERIC POLLUTANT DISPERSION RELEASED FROM LINE SOURCE |
ANALYTICAL STUDY OF THE EXCESS ENTHALPY IN THE COMBUSTION WITHIN POROUS MEDIA |
APPLICATION OF THE MAXIMUM ENTROPY PRINCIPLE TO THE ANALYSIS OF A DIESEL ENGINE FUEL SPRAY. |
BI-DIMENSIONAL RECONSTRUCTION OF A BUNSEN BURNER FLAME |
CHEMILUMINESCENCE SENSOR FOR 3D NOX CHARACTERIZATION IN LEAN-PREMIXED FLAME COMBUSTION PROCESSES |
COMPARATIVE STUDY OF THE EMISSIONS LEVELS/PASSENGER RATES BETWEEN HEAVY-DUTY AND LIGHT-DUTY VEHICLES IN URBAN TRAFFIC |
DETERMINATION OF ACTIVATION ENERGY IN THE COMBUSTION PROCESS BY THERMOGRAVIMETRIC ANALYSIS |
DEVELOPMENT OF A RADIANT POROUS BURNER WITH A COMBINED THERMAL AND FLUIDYNAMIC MECHANISM OF FLAME STABILIZATION |
DIRECT CLIMATIC FORCING DUE TO ATMOSPHERIC AEROSOLS FROM BIOMASS BURNING IN BRAZIL |
ECOTEC - ECONOMY, ECOLOGY AND TECHNOLOGY. A RATIONAL APPROACH TO THE RESOURCES MANAGEMENT PROBLEM |
EFFECTS OF DIAMETER AND HEAT FLUX ON BURNING CHARACTERISTICS OF WOOD CYLINDERS |
EFFECTS OF MOISTURE CONTENT ON BURN RATES AND CHARACTERISTIC TIMES OF BRAZILIAN WOODS |
EXPERIMENTAL STUDY OF THERMAL REGENERATION OF FOUNDRY SAND IN A FLUIDIZED BED INCINERATOR |
FUEL CONTROL NETWORK FOR A MULTIPLE FUEL BOILER |
HEAVY METALS RECOVERY FROM INDUSTRIAL WASTEWATER USING FLUIDIZED BED ELECTROCHEMICAL REACTOR |
INFLUENCE OF INTEGRAL LENGTH SCALES ON SAND EROSION TECHNIQUES |
LOW COST ENERGY GENERATION SYSTEM USING BIOGAS FROM A SANITARY LANDFILL |
MATHEMATICAL AND EXPERIMENTAL INVESTIGATION OF A DOWNDRAFT GASIFIER. |
NEGATIVE ASPECTS OF THE CUTTING FLUID APPLICATION IN METAL-WORKING PROCESS FOR THE ENVIRONMENT AND WORKERS' HEALTH |
NOX FORMATION IN CO-PROCESSING OF USELESS TIRES IN THE CEMENT INDUSTRY CLINKER KILNS |
NUMERICAL ANALYSES OF NOX FORMATION IN CYCLONE COMBUSTORS FED WITH AIR AND SAWDUST |
NUMERICAL EXPERIMENTS OF INDUCED EDDIES IN THE COASTAL OCEAN |
NUMERICAL MODEL OF A BURNING WOOD CYLINDER |
PARAMETRIC STUDY OF A CONFINED STAGNATION METHANE-AIR DIFFUSION FLAME |
PREDICTION OF THE REYNOLDS STRESSES IN TURBULENT SHEAR FLOWS WITH THE USE OF STOCHASTIC DIFFERENTIAL EQUATIONS |
RELATIONS BETWEEN PHYSICALS PROPERTIES OF SOLID FUELS AND ITS REACTIVITY |
SIMULATION OF COMBUSTION IN CLYLINDRICAL CHAMBER |
STILL FURNACE OPTIMIZATION |
TESTING OF A 30 KWE STATIONARY RECIPROCATING ENGINE IN DIFFERENT OPERATIONAL LOADS - PERSPECTIVE OF THE MICROCOGENERATION USING NATURAL GAS |
THE INFLUENCE OF RECIRCULATION INTENSITY ON CO AND NO EMISSIONS |
THE PERFORMANCE OF REFLECTIVE AND ABSORPTIVE NOISE BARRIER IN CITROSUCO`S INDUSTRY IN MATÃO (SP) - BRAZIL |
THERMAL ANALYSIS OF THE BURN OF DIESEL OIL AND BIODIESEL IN A FLAME TUBE FURNACE |
THERMOHIDRAULIC DESIGN AND ECONOMICAL ANALYSIS OF A HEAT RECOVERY PROCESS IN A FLUIDIZED BED HEAT EXCHANGER |
USE OF BIOGAS ON SMALL POWER GENERATORS |
VALIDATION OF A NUMERICAL SIMULATION OF THE COMBUSTION OF NATURAL GAS IN A CYLINDRICAL CHAMBER |
WIND TUNNEL SIMULATION OF THE ATMOSPHERIC FLOW AND DISPERSION PROCESS IN AN URBAN AREA |
|
top |
|
DYNAMICS, SOLID MECHANICS AND OPTIMIZATION |
2D ELASTODYNAMIC WITH BOUNDARY ELEMENT METHOD AND THE OPERATIONAL QUADRATURE METHOD |
3D EFFECTS ON J-Q TRAJECTORIES FOR FRACTURE SPECIMENS AND APPLICATIONS TO CORRELATE FRACTURE BEHAVIOR |
A COMBINED LAYOUT OPTIMIZATION WITH AN H-ADAPTIVE PROCEDURE APPLIED TO PLATE PROBLEMS |
A COMPARATIVE STUDY OF NEURAL NETWORKS AND SENSITIVITY MODAL ANALYSIS FOR DAMAGE ASSESMENT |
A COMPARISON OF METAMODELING TECHNIQUES ADDRESSING THE NUMBER OF INDEPENDENT VARIABLES AND THE PRESENCE OF NOISY DATA |
A COMPARISON OF TWO MODAL CONTROL STRATEGIES FOR THE ACTIVE VIBRATION CONTROL OF A TRUSS STRUCTURE. |
A CRITICAL EVALUATION OF THREE MODELS OF EXTERNAL BALLISTICS |
A FEATURE BASED DESIGN (FBD) METHOD EMBEDDED WITH DESIGN FOR MANUFACTURING (DFM) CAPABILITY. |
A FRAMEWORK FOR METAL FORMING SIMULATION |
A LOCKING-FREE LAMINATED COMPOSITE PLATE FINITE ELEMENT |
A MATRIX METHOD FOR TORSIONAL VIBRATION OF MULTI-STEP NON-UNIFORM RODS |
A MIXED MODEL AND AN ALGORITHM FOR VISCOPLASTICITY |
A NEW MOUNTING DESIGN FOR STEAM DISTRIBUTOR PLATES IN FIRST STAGE DEHYDROGENERATOR MIXERS |
A NUMERICAL INVESTIGATION ON TRANSIENT WAVE PROPAGATION PHENOMENA AT 2D HALF-SPACES AND THE TRANSIENT RESPONSE OF RIGID SURFACE FOUNDATIONS |
A PLATE FINITE ELEMENT COUPLING FIRST ORDER MODEL AND A POSTERIORI ERROR ESTIMATOR |
A PROCEDURE TO DETERMINE THE IMPACT COEFFICIENT IN A LINEAR ELASTIC STRAIGHT BEAM CONSIDERING THE EXACT CURVATURE OF THE ELASTICA |
A SHAPE OPTIMIZATION PROCEDURE FOR FLUID FLOW PROBLEMS |
A STRESS BASED H-ADAPTIVE TOPOLOGY OPTIMIZATION METHOD |
A VARIATIONAL FORMULATION OF NONLINEAR VISCOELASTIC MODELS IN FINITE STRAIN REGIME |
ACCELERATION OF GENETIC ALGORITHMS FOR THE DESIGN
OF RANDOM MICRO-HETEROGENEOUS MATERIALS |
ACTIVE SHAPE CONTROL OF A BEAM BY MEANS OF
SHAPE MEMORY ACTUATORS |
AN APPLICATION OF ARMAV MODEL TO THE IDENTIFICATION OF MODAL PARAMETERS |
AN ERROR ESTIMATOR AND A MESH REFINEMENT STRATEGY FOR THE MODIFIED ELEMENT-FREE GALERKIN METHOD |
AN EXACT SOLUTION FOR THE HARDY CROSS METHOD THROUGH A MATRICIAL FORMULATION APPLIED TO CONTINUOUS BEAMS |
AN EXTENSION OF THE MODIFIED ELEMENT FREE GALERKIN METHOD APPLIED TO LARGE DEFORMATION PROBLEMS |
AN INDUCED ANISOTROPY DAMAGE MODEL APPLIED TO TWO-DIMENSIONAL SOLID ANALYSIS |
AN INTRODUCTION TO THE ACTIVE CONTROL OF VIBRATION IN ROTOR UNBALANCE USING MAGNETIC BEARING |
ANALYSIS AND IDENTIFICATION OF THE DYNAMICS OF VIBRATION'S COMPLEX SYSTEM |
ANALYSIS OF BIFURCATION AND CHAOS IN A COUPLED RAYLEIGH OSCILLATORS SYSTEM APPLIED IN THE LOCOMOTION OF A BIPEDAL ROBOT |
ANALYSIS OF COMPOSITE SLEEVE REINFORCEMENT SYSTEMS FOR METALLIC PIPELINES WITH LOCALIZED IMPERFECTIONS OR DAMAGE |
ANALYSIS OF INTERNAL SUBLOOPS DUE TO INCOMPLETE PHASE TRANSFORMATIONS IN SHAPE MEMORY ALLOYS |
ANALYSIS OF LAMINATED COMPOSITE PLATES WITH TRANSVERSE CRACKS BY MLGFM SOLUTION |
ANALYSIS OF PERFORMANCE OF DIFFERENT NUMERICAL METHOD TO CAPTURE THE SCALE EFFECT |
ANALYSIS OF ROTOR DYNAMICS DEFECTS USING VIBRATION BASED MONITORING |
ANALYSIS OF SIMPLIFIED PROJECTION TECHNIQUES TO ESTIMATE THE STRESS AND STRAIN HISTORIES IN NOTCHED METALLIC PARTS UNDERGOING CYCLIC INELASTIC DEFORMATIONS |
ANALYSIS OF THE S PACER GRIDS STIFNESS INFLUENCE IN THE DETERMINATION OF THE NATURAL FREQUENCIES OF NUCLEAR PLANTS FUEL AS SEMBLIES |
ANALYSIS OF VIRTUAL DEVELOPMENT TOOLS FOR THE VIRTUAL PROTOTYPING OF A MOBILE AGRICULTURAL PLATFORM |
ANALYTIC MODEL OF THE CYLINDRICAL SHELL MOTION EQUATIONS |
APPLICATION OF A MESOSCOPIC SCALE APPROACH ASSOCIATED WITH A NOTCH ANOLOGUE TECHNIQUE FOR FRETTING FATIGUE |
APPLICATION OF NUMERICAL METHODOLOGIES IN THE DYNAMIC ANALYSIS OF HYDROGENERATORS. |
ARTIFICIAL NEURAL NETWORK STUDY APPLIED TO RIGID ROTOR DYNAMIC BALANCING |
ASSESSING THE QUALITY OF PRODUCT DESIGN FROM THE DESIGNER'S POINT OF VIEW |
ASYMPTOTIC WAVE PROPAGATION ALONG CHAINS OF REPETITIVE SYSTEMS |
BALANCING METHODOLOGY OF A RIGID ROTOR USING ARTIFICIAL NEURAL NETWORK |
BOUNDARY ELEMENT FUNDAMENTAL TENSORS FOR AXISYMMETRIC LINEAR ELASTICITY PROBLEMS
|
CLASSIFYING SYNTHESIZED AND REAL VOICE PATTERNS USING NEURAL NETWORKS |
COMPLEX BEHAVIOR OF AN EXPERIMENTAL NONLINEAR PENDULUM: CHAOS AND TRANSIENT CHAOS |
COMPUTATIONAL ASPECTS OF TWO DIFFERENT GEOMETRICALLY NONLINEAR STRUCTURAL TIME DISCRETIZATION MODELS FOR FLUID-STRUCTURE INTERACTION PROBLEMS |
COMPUTING THE EFFECTIVE HOMOGENIZED MECHANICAL PROPERTIES FOR TOPOLOGICAL STRUCTURAL OPTIMIZATION |
CORRELATION OF KT MAGNITUDE AND LEVEL OF CONSERVATISM OF LOCAL STRAIN ELASTOPLASTIC MODELS |
CRACK PROPAGATION STRENGTH OF A ENVIRONMENT CORROSION RESISTANT STRUCTURAL STEEL |
DAMAGE IDENTIFICATION USING FREQUENCY RESPONSE FUNCTIONS |
DEFLECTIONS OF THIN PLATES: INFLUENCE ANALYSIS OF THE SLOPE OF THE PLATE IN THE APLICATION OF LINEAR AND NONLINEAR THEORY |
DESIGN AND CONSTRUCTION OF A PRECRACKING FOR FATIGUE FOR THE DETERMINATION OF THE FRACTURE TOUGHNESS |
DETECTION OF IMPERFECTIONS IN ROTATING MACHINES THROUGH ARTIFICIAL NEURAL NETWORKS
|
DETERMINATION OF 5052 ALUMINUM ALLOY ACOUSTOELASTIC COEFFICIENTS |
DETERMINATION OF STRESS INTENSITY FACTORS DUE TO THERMAL STRESSES USING ISOCHROMATIC FRINGE PATTERS |
DETERMINATION OF TRUE STRESS-STRAIN CURVE FOR ISOTROPIC MATERIALS WITH THIN SHEET TENSILE SPECIMENS |
DETERMINATION OF UNCERTAINTY OF A REFERENCE PRESSURE TRANSDUCER TRANSFER FUNCTION IN FREQUENCY BELOW 100 HZ |
DIAGNOSE OF FAULTS IN MECHANICAL SYSTEMS WITH UNKNOWN INPUTS USING PROPORTIONAL AND INTEGRAL STATE OBSERVERS |
DISC-DISC GEOMETRY AS AN ALTERNATIVE TO THE FZG TEST METHOD |
DISPLACEMENT OF SEMI-INFINITE BEAMS ON AN ELASTIC FOUNDATION UNDER BENDING-COMPRESSION LOADING |
DISPLACEMENT-BASED FINITE ELEMENT FORMULATION OF ACOUSTIC FLUID-STRUCTURE INTERACTION WITH LOCALIZED LAGRANGE MULTIPLIERS |
DYNAMIC ANALYSIS OF A ROTOR-BEARING SYSTEM BY FINITE ELEMENTS |
DYNAMIC ANALYSIS OF SLENDER COLUMNS UNDER SELF-WEIGHT USING DIGITAL IMAGE PROCESSING TECHNIQUES |
DYNAMIC BEHAVIOR OF FLEXIBLE BEAMS WITH VISCOELASTIC LAYER TREATMENT |
DYNAMIC MODELLING OF THE CRANK MECHANISM AND HYDRODYNAMIC BEARINGS OF COMBUSTION ENGINES |
DYNAMICAL ANALYSIS OF TRANSMISSION LINE CABLES THROUGH NONLINEAR MODELS |
DYNAMICAL BEHAVIOUR OF A WHEELCHAIR UNDER MOST COMMON DEFORMITY OF PROPULSION CYCLE |
DYNAMICS OF MARINE PIPELINES - A NON-LINEAR ANALYSIS |
EFFECT OF THE PRESENCE OF SOLID CONTAMINATION AND THE RESULTING WEAR ON THE MECHANICAL SIGNATURE OF BALL BEARINGS |
EFFICIENT PROCEDURE TO CALCULATE TRANSMISSION ERROR OF HELICAL GEAR PAIRS WITH GLOBAL TOOTH CONTACT ANALYSIS USING A COMBINED PSEUDO-INTERFERENCE AND LINEAR PROGRAMMING SOLUTION |
ELASTOPLASTIC ANALYSIS OF FUNCTIONALLY GRADED MATERIALS |
ENHANCING TIME-FREQUENCY REPRESENTATIONS FOR FAULT ANALYSIS IN GEARED SYSTEMS |
ENLARGED COMPRESSION CHAMBER IN HIGH PRESSURE - HIGH TEMPERATURE MULTI-ANVIL DEVICE. |
ESTIMATE OF THE RENDEZVOUS TRAJECTORY THROUGH THE DYNAMICS OF THE RELATIVE MOTION - FORMATION FLYING |
EVALUATION OF LOCAL STRAIN MODELS IN THE SIMULATION OF ELASTOPLASTIC CONDITION AT THE NOTCH ROOT OF THICK PLATES |
EXPERIMENTAL AND NUMERICAL DYNAMIC ANALYSIS OF A CRACKED BEAM |
EXPERIMENTAL EVALUATION OF OIL FILM THICKNESSES IN A TILTING PAD HYDRODYNAMIC THRUST BEARING. |
EXPERIMENTAL IDENTIFICATION OF IN-PLANE LOADS IN RECTANGULAR PLATES USING LIFECYCLE MODEL |
EXPERIMENTAL INVESTIGATION OF THE DYNAMIC BEHAVIOR OF STOCKBRIDGE DAMPERS |
EXPERIMENTAL, NUMERICAL AND ANALYTICAL INVESTIGATION OF THE PRYING ACTION AND CONTACT STRESSES IN T-STUB STEEL CONNECTIONS |
FATIGUE CRACK GROWTH BEHAVIOUR OF A USI-SAC-50 HOT-ROLLING STEEL IN THICKNESS DIFFERENTS |
FAULT IDENTIFICATION IN ROTOR SYSTEM USING MODEL BASED METHODS, EXPERIMENTAL DATA AND ARTIFICIAL NEURAL NETWORK |
FINITE DEFORMATIONS AND INSTABILITIES OF STRESSED CYLINDRICAL TUBES UNDER HYDROSTATIC PRESSURE |
FINITE ELEMENT ANALYSIS APPLIED TO SHAPE MEMORY TRUSSES USING ABAQUS |
FINITE ELEMENT ANALYSIS OF THE THERMOMECHANICAL COUPLING EFFECTS ON DAMAGE LOCALIZATION IN ELASTOPLASTIC METALLIC BARS |
FINITE STRAINS AND VOLUMETRIC LOCKING STUDIES ON THE MEFG |
GENERALIZED EXTREMAL OPTIMIZATION APPLIED TO THREE-DIMENSIONAL TRUSS DESIGN |
GENERALIZED FINITE ELEMENT METHOD ON THE LOCKING PROBLEM OF DEGENERATED 3-D TRIANGULAR SHELL ELEMENTS |
H-INF CONTROL WITH POLE PLACEMENT CONSTRAINTS FOR FLEXIBLE STRUCTURES VIBRATION REDUCTION
|
HIERARCHICAL METHODS APPLIED TO FREE VIBRATION OF EULER-BERNOULLI BEAMS |
HOW TO PREDICT THE VIBRATION EFFECT DUE TO THE MACHINE OPERATION ON ITS VICINITY |
HYDRODYNAMIC LUBRICATION APPLIED TO BEARINGS WITH OSCILLATING MOTION |
IDENTIFICATION OF A RANDOM ELASTIC MEDIUM BY VIBRATION TESTS |
IMPLEMENTATION OF THE HYBRID PARADIGM OF WEIGHT'S INITIALIZATION FOR APPLICATION IN ARTIFICIAL NEURAL NETWORKS MULTILAYER
|
IMPORTANCE OF THE RELIABILITY REQUIREMENTS EVALUATION IN THE INITIAL PHASES OF THE DEVELOPMENT OF AN EQUIPMENT FOR THE MECHANIZATION OF THE MARICULTURE |
INFLUENCE OF THE AXIAL WEDGE EFFECT ON THE STATIC EQUILIBRIUM POSITION OF HYDRODYNAMIC JOURNAL BEARINGS. |
INFLUENCE OF THE BACKING AND COVERING LAYERS THICKNESSES IN THE STRESS FIELDS IN AUTOMOTIVE JOURNAL BEARINGS |
INFLUENCE OF THE GEOMETRICAL NON-UNIFORMITY HOUSING SUPPORTS IN THE AUTOMOTIVE JOURNAL BEARINGS STRESSES DISTRIBUTION |
INFLUENCE OF TOOTH GEOMETRY ON THE STRENGTH OF PLASTIC SPUR GEARS. |
INTERNALLY PRESSURIZED ALUMINIUM PIPES STRENGTHENED WITH A COMPOSITE REPAIR |
JOURNAL BEARING ORBITS FITTING WITH HYBRID META-HEURISTIC METHOD |
LOOKING FOR OPTIMAL TOPOLOGIES IN 2D POTENTIAL PROBLEMS WITH GENETIC ALGORITHMS AND BEM |
MATERIAL AND GEOMETRIC DISPERSION EFFECTS ON LONGITUDINAL ACOUSTIC DISTURBANCES IN A DUMILOAD FOR SONAR TRANSDUCERS |
MEASURING THE STRESS AMPLITUDE WITHIN THE CONTEXT OF MULTIAXIAL FATIGUE |
MECHANICAL DESIGN OF TWO INSTRUMENT SUPPORT MODULES FOR THE SOAR TELESCOPE |
METHODOLOGY TO EVALUATE VIBRATION INCREASE DUE TO THERMAL ROTOR BOW - A COMPARISON BETWEEN ALUMINUM AND COPPER CAGES USED IN INDUCTION MOTORS |
MODAL ANALYSIS OF HYDROGENERATORS USING CONDENSATION TECHNIQUES |
MODELING AND CONTROL OF AN EULER-BERNOULLI BI-SUPPORTED BEAM. |
MODELING RESIDUAL STRESSES IN WELDED STEEL PLATES USING A CONSTITUTIVE MODEL WITH PHASE TRANSFORMATION |
MODELING TRANSFORMATION INDUCED PLASTICITY IN SHAPE MEMORY ALLOYS |
MODELLING AND PARAMETER ESTIMATION OF TRANSMISSION LINES |
MODELS OF SPACE ENERGETICS OF COUPLED STRUCTURAL
SYSTEMS AT AN ARBITRARY ANGLE |
NEW CRITERION OF AUTOMATIC CHOICE OF MODES USED IN MODAL SYNTHESIS METHOD |
NOISE SOURCES IDENTIFICATION ON A LARGE STAMPING PRESS |
NON LINEAR MODEL FOR COUPLED AXIAL/TORSIONAL VIBRATIONS OF DRILL-STRINGS |
NON-LINEAR ANALYSIS OF BUILDING FLOOR STRUCTURES BY THE BOUNDARY ELEMENT METHOD |
NONLINEAR DYNAMICS OF A SHAPE MEMORY OSCILLATOR USING A CONSTITUTIVE MODEL WITH INTERNAL CONSTRAINTS |
NUMERICAL AND EXPERIMENTAL INVESTIGATIONS OF THE NONLINEAR DYNAMICS AND CHAOS IN NON-SMOOTH SYSTEMS WITH DISCONTINUOUS SUPPORT |
NUMERICAL EVALUATION OF COLDWORKED RIVETED JOINTS |
NUMERICAL IMPLEMENTATION OF AN ORTHOTROPIC PLASTICITY MODEL IN THE ABAQUS FINITE ELEMENT CODE AND ASSOCIATED SIMULATIONS OF SHEET METAL FORMING TESTS |
NUMERICAL SCHEMES FOR SIMULATION OF COUPLED AXIAL/TORSIONAL VIBRATIONS OF DRILL STRINGS |
NUMERICAL STABILITY ANALYSIS OF COMPOSITE PLATES THERMALLY STIFFENED BY FINITE ELEMENT METHOD |
ON A THEORY OF ELASTICITY COUPLED WITH DAMAGE AND DIFFUSION |
ON LINE MONITORING OF RELIABILITY OF SIGNALS TO BE USED TO CONTROL PURPOSES |
ON MEASURES OF NONLINEARITIES FOR DYNAMICAL SYSTEMS WITH UNCERTAINTIES. |
ON NON-LINEAR DYNAMIC BEHAVIOR OF THE HODGKIN-HUXLEY MODEL |
ON THE HYPOTHESIS AND LIMITATIONS OF TRADITIONAL METHODOLOGIES FOR MECHANICAL DESIGN OF A FILLET WELDED SIMPLE STRUCTURE |
ON THE INTERACTION BETWEEN FATIGUE CRACK BRANCHING AND CLOSURE |
ON THE PHASE TRANSFORMATION EFFECT IN RESIDUAL STRESSES GENERATED BY QUENCHING IN NOTCHED STEEL CYLINDERS |
ON THE USE OF ARTIFICIAL NEURAL NETWORKS IN THE ESTIMATION OF RESIDUAL LIFE OF FATIGUE-CRACKED SHEET SAMPLES |
OPTIMAL DESIGN AND LOCATION FOR A VISCOELASTIC DYNAMIC NEUTRALIZER SYSTEM USING GENETIC ALGORITHM |
OPTMIZATION OF PI CONTROLLER BASED ON HYBRID SIMPLEX-GENETIC APPROACH APPLIED TO A THERMAL SYSTEM |
OUTPUT-ONLY MODAL ANALYSIS USING FREQUENCY DOMAIN DECOMPOSITION |
PERFORMANCE ANALYSIS OF
FUNCTIONALLY GRADED THERMAL BARRIERS
|
PRODUCT STRATEGIC DEVELOPMENT (PSD) IN THE AVIATION SEGMENT |
PRODUCTIVITY CENTERED PRODUCT DESIGN |
RISK BASED DECISION MAKINBG APPLIED TO MAINTENANCE POLICY SELECTION |
ROBOT PATH PLANNING: AVOIDING OBSTACLES |
ROBUST-H-INFINITE CONTROL FOR FLEXIBLE STRUCTURES WITH REDUCED DYNAMICS
|
ROTOR BALANCING IN NON-STATIONARY CONDITION BY THE USE OF ADAPTIVE FILTER |
SENSITIVITY ANALYSIS OF MECHANICAL COUPLINGS MODEL APPLYING FREQUENCY RESPONSE FUNCTIONS |
SIMULATION OF RADIATION
CONDITION IN ROTATING MACHINERY USING SIMPLIFIED MODELS |
SOLUTION OF BUCKLING EIGENPROBLEMS THROUGH A NEW VARIANT OF THE LANCZOS ALGORITHM |
SOME ASPECTS IN THE USE ON THE KARHUNEN-LOÈVE DECOMPOSITION FOR ANALYZING VIBRATING SYSTEMS |
SOME INSIGHTS INTO THE DYNAMIC RESPONSE OF FLEXIBLE ROTORS SUPPORTED ON FLUID FILM BEARINGS |
STABILITY AND VIBRATION ANALYSIS OF SLENDER L-FRAMES
WITH SEMI-RIGID CONNECTIONS |
STATISTICAL ANALYSIS OF VIBRATION SIGNALS FOR CONDITION MONITORING OF DEFECTS IN ROLLING ELEMENT BEARINGS. |
STICK-SLIP ANALYSIS IN DRILL STRINGS |
STRESS RELAXATION IN WELDING JOINTS OF 5052 ALUMINUM USING THE ULTRASONIC METHOD |
STRUCTURAL ANALYSIS IN DESIGNING CONICAL DISCS OF ROTATION |
STRUCTURAL INTEGRITY ASSESSMENTS OF AUSTENITIC STAINLESS STEEL PIPES WITH AXIAL FLAWS |
SYSTEMS DYNAMICS TECHNIQUES UTILIZATION IN BUSINESS STRATEGY MODELING |
TECHNIQUE OF PARAMETERS AND INPUTS IDENTIFICATION IN MECHANICAL SYSTEMS |
TECHNOLOGY MANAGEMENT IN PRODUCT DESIGN PROCESS FOR MICRO AND SMALL-SIZED METAL MECHANIC COMPANIES |
THE EFFECTS OF UNBALANCE AND CLEARANCE ON THE BEARINGS OF AN OVERHUNG ROTOR |
THE IMPLICITLY RESTARTED ARNOLDI METHOD APPLIED TO TUNED VIBRATION ABSORBERS PROBLEMS |
THE IMPOSITION OF THE INJECTIVITY CONSTRAINT
ON A FAMILY OF THREE-DIMENSIONAL ELASTICITY PROBLEMS
|
THE INFLUENCE OF SHEET THICKNESS ON DRAWBEAD RESTRAINING FORCE IN SHEET METAL FORMING |
THE PRINCIPLES OF INCLUSIVE DESIGN |
THE WIND CONSIDERED AS A NON-IDEAL EXCITATION IN MODEL OF A WIND TURBINE TOWER WITH IMPACT DAMPER |
THERMOMECHANICAL COUPLING EFFECTS ON LOW-CYCLE FATIGUE LIFE OF METALLIC MATERIALS |
TOPOLOGICAL SENSITIVITY ANALYSIS APPLIED TO THREE-DIMENSIONAL LINEAR
ELASTICITY TOPOLOGY DESIGN |
TOPOLOGY OPTIMIZATION METHOD APPLIED TO DESIGN HYDRO GENERATOR COMPONENTS UNDER BODY FORCES |
TRAJECTORY MODELING OF CAPAMAN (CASSINO PARALLEL MANIPULATOR)
BY USING 4TH ORDER B-SPLINES .
|
UNDERWATER VEHICLE DYNAMIC MODELING |
VARIABLE STRUCTURE CONTROL DESIGN BASED ON DIFFERENTIAL EVOLUTION OPTIMIZATION
WITH NEW SINOSOIDAL GAUSSIAN OPERATOR
|
VIBRATION ANALYSIS OF ROTATING SHAFTS COUPLED BY RIGID DISKS |
|
top |
|
ENERGY AND TRANSPORT PHENOMENA |
3-D TRANSIENT SIMULATION OF AN AXISYMMETRIC MICRO HEAT PIPE |
A CHEMICAL EQUILIBRIUM BASED MODEL FOR BIOMASS GASIFICATION |
A COMPARATIVE STUDY OF FINITE VOLUMES, FINITE DIFFERENCES AND MESHLESS METHODS FOR DRIVEN CAVITY PROBLEM |
A COMPARISON BETWEEN NUMERICAL AND LABORATORY DATA FOR TWO-DIMENSIONAL STEEP TOPOGRAPHIC ELEVATION |
A FINITE VOLUME METHOD FOR SIMULATION OF POLYMER MELT FLOW IN CLOSED CHANNELS |
A MIXTURE THEORY DESCRIPTION FOR UNSATURATED FLOWS CONTAINING POLLUTANTS |
A MODEL FOR FREQUENCY-DEPENDENT FRICTION IN ONEDIMENSIONAL UNSTEADY FLUID FLOWS |
A NEW MAINTENAINCE METHODOLOGY APPLIED TO A HVAC SYSTEM |
A NEW TECHNIQUE TO IMPROVE COMPLETENESS CONDITIONS IN QUASI-DUAL BOUNDARY ELEMENT FORMULATION |
A NUMERICAL STUDY OF INFLUENCE OF THE ASPECT RATIO IN COMBINED FORCED AND FREE CONVECTION HEAT TRANSFER IN A SEMIPOROUS OPEN CAVITY |
A NUMERICAL STUDY OF NATURAL CONVECTION IN AN INTERNAL FINNED ANULUS WITH CONDUCTION IN THE HORIZONTAL CYLINDERS AND FINS |
A PARTICLE METHOD FOR AIRCRAFT WAKE BEHAVIOR ANALYSIS NEAR THE GROUND USING TURBULENCE MODELING |
A SEMI EMPIRICAL METHOD FOR DESIGN OF A STEAM PIPING AND ITS CONDENSATE RECOVERY SYSTEM |
A SIMPLIFIED APPROACH TO NATURAL CONVECTION MODELLING IN COOLING TOWERS BY NEURAL NETWORKS |
A STUDY OF INCREMENT CASE OF THE COGENERATION IN SUGAR INDUSTRY FOR THE ECUADORIAN CONTEXT
|
A THEORETICAL STUDY OF AN EMULSION OF HIGH VISCOSITY DROPS UNDER SHEAR |
A TURBULENCE MODEL FOR THE PREDICTION OF THE HEAT TRANSFER REDUCTION OF VISCOELASTIC FLUID FLOWS |
ABSORPTION OF REFRIGERANT MIXTURES IN LUBRICANT OIL |
ACCELERATION LENGTHS IN VERTICAL PNEUMATIC CONVEYING OF CORK STOPPERS |
AN ANALYTICAL SOLUTION FOR THE SECOND ORDER MATRIX GITT TRANSFORMED DIFFERENTIAL EQUATION BY THE LAPLACE TRANSFORM TECHNIQUE |
AN EFFICIENT NUMERICAL MODEL FOR ISOTHERMAL AND THERMALLY COUPLED INCOMPRESSIBLE FLOWS |
AN EXPERIMENTAL AND THEORETICAL ANALYSIS OF A PEM FUEL CELL COOLING SYSTEM |
AN INVERSE ANALYSIS FOR SIMULTANEOUS THERMAL PARAMETER ESTIMATION IN ADSORPTIVE POROUS PACKED BEDS |
ANALISYS OF THE ANALYTICAL RESOLUTION OF THE RADIATIVE TRANSFER EQUATION BY FOR AN OBLIQUELY INCIDENT COLLIMATED BEAM ONTO THE SURFACE |
ANALYSIS OF A HIGH TEMPERATURE THERMOSYPHON |
ANALYSIS OF CONTACT ANGLE IN CAPILLARY INVASION |
ANALYSIS OF DAYLIGHTING IN THE ENERGY SAVINGS OF ARTIFICIAL LIGHTING AND AIR CONDITIONING SYSTEMS OF COMMERCIAL BUILDINGS |
ANALYSIS OF PLUVIAL FLOW IN METALLIC TILES |
ANALYSIS OF POWER AND ENERGY IN ELECTROCHEMICAL PORTABLE POWER SYSTEMS |
ANALYSIS OF PURELY KINEMATIC CRITERIA FOR FLOW CLASSIFICATION |
ANALYSIS OF RADIATIVE PROPERTIES IDENTIFICATION WITH REFRACTIVE INDEX |
ANALYSIS OF SWIRL TUBE AS DOWNHOLE DESANDER DEVICE |
ANALYSIS, SIMULATION AND FEASIBILITY STUDY OF A DIRECT COMPRESSION DESALINATION SYSTEM |
ANALYTICAL DEDUCTION OF THE RELATION BETWEEN THE MAXIMUM AND AVERAGE VELOCITIES IN PIPES OF SQUARE AND RECTANGULAR SHAPED SECTION |
ANISOTROPIC CORRECTIONS AS A FUNTION OF THE CLEARNESS INDEX KT FOR THE DIFFUSE SOLAR IRRADIANCE MEASURED BY THE MELO-ESCOBEDO SHADOWRING METHOD |
APPARENT WALL SLIP IN THE FULLY DEVELOPED LAMINAR FLOW
OF VISCOPLASTIC LIQUIDS THROUGH TUBES |
APPLICATIONS OF HIGHER-ORDER UPWIND DISCRETIZATIONS FOR CALCULATING INCOMPRESSIBLE FLUID FLOWS |
ASSESSMENT OF TURBULENCE MODELLING FOR CFD SIMULATIONS OF HYDROTURBINES: DRAFT TUBES |
ASYMMETRIC RECTANGULAR OBSTRUCTIONS ON ENTRANCE REGIONS OF FLAT PLATE CHANNELS |
ATTAINMENT OF KINETIC MECHANISM GENERAL EQUATION OF THE CARBONIZATION OF EUCALYPTUS SPP WITH DETERMINATION OF HEMICELULOSE, CELLULOSE AND LIGNINA CONTENT |
BI-PHASE FLOW CHARACTERIZATION BY ULTRASONIC METHODOLOGY
|
BIOMASS GASIFICATION AND FUEL CELL INTEGRATION: THE POTENTIAL AND EFICIENCY |
BOND GRAPH MODELING OF INCOMPRESSIBLE THERMOFLUID FLOWS. |
CALIBRATION METHODOLOGY OF A F101-F201 GLOBAL FLOW PROBE USING A LASER DOPPLER ANEMOMETER |
CAPACITIVE SENSOR FOR DYNAMIC GAS-LIQUID PHASE DETECTION IN TWO-PHASE FLOWS |
CHARACTERISTICS OF AIR-WATER VERTICAL TWO-PHASE FLOW ACROSS A SUDDEN EXPANSION |
CHARACTERIZATION OF SLUG FLOWS IN HORIZONTAL PIPING BY SIGNAL ANALYSIS FROM A CAPACITIVE PROBE |
COMPARATIVE ANALYSIS BETWEEN HEATING CIRCUITS FOR BASEBOARD CONVECTORS |
COMPARATIVE STUDY BETWEEN SAVONIUS ROTOR MADE ON TWO OR THREE BLADES OF POLYETHYLENE |
COMPARISON OF INDEPENDENT HEAT TRANSFER RESULTS AND PREDICTION METHODS FOR FLOW BOILING IN MICRO-SCALE CHANNELS |
COMPARISON OF MODELS FOR THE STEADY-STATE ANALYSIS OF TILTING-PAD THRUST BEARINGS |
COMPOSITE FOR THERMAL ISOLATION IN HOT WATER CONDUCTORS TUBES IN SYSTEMS OF HEATING FOR SOLAR ENERGY |
COMPUTATIONAL MODELING AND THERMODYNAMIC ANALYSIS OF COMBINED CYCLES USING BLACK LIQUOR GASIFICATION |
CONFINED NUCLEATE BOILING OF FC72 ON A DOWNWARD OR UPWARD FACING COPPER DISC |
CONJUGATE NATURAL CONVECTION APPLIED TO THE ELECTRONIC COMPONENT COOLING |
CONSTRUCTAL DESIGN OF A TRAPEZOIDAL ISOTHERMAL CAVITY INTO A SOLID CONDUCTING WALL |
CONTAMINANT DISPERSION SIMULATION BY SOLVING THE THREE-DIMENSIONAL ADVECTION-DIFFUSION EQUATION COMBINING THE GILTT AND ADMM METHODS |
CONTINUOUS AND INTERMITTENT DRYING (TEMPERING) OF OBLATE SPHEROIDAL BODIES: MODELING AND SIMULATION |
COOLING WATER INFLUENCE IN TEMPERATURE PROFILE OF CONTINUOUS CASTING MOLD |
CORRELATIVE ANALYSIS IN TIME AND SPACE OF TURBULENT BOUNDARY LAYER OVER PERMEABLE POROUS SLAB |
CRITICAL EVALUATION OF TECHNICAL-ECONOMIC POTENTIAL OF ELECTRIC ENERGY SELF-GENERATION IN BRAZIL |
CRITICAL EVALUATION OF THE SHEAR-STRESS TRANSPORT (SST) K-W TURBULENCE MODEL |
CYLINDRICAL ENCAPSULATED COLD STORAGE |
DES SIMULATION OF A FINITE CYLINDER MOUNTED ON A FLAT PLATE |
DESIGN AND CONSTRUCTION OF A 10 KW HORIZONTAL AXIS WIND TURBINE (HAWT) WITH VARIABLE SPEED |
DETERMINATION OF ENERGY PERFORMANCE OF AIR CONDITIONING SYSTEMS USING PSYCROMETRIC ANALYSIS |
DEVELOPMENT OF A PIV SYSTEM USING A LASER-DIODE |
DEVELOPMENT OF A TEST RIG FOR SONIC NOZZLES |
DEVELOPMENT OF AN ADAPTIVE MULTIVARIABLE CONTROLLER FOR A REFRIGERATION SYSTEM USING TRANSFER FUNCTIONS GENERATED BY A WHITE BOX MATHEMATICAL MODEL |
DEVELOPMENT OF METHODOLOGY AND SOFTWARE FOR ANALYSIS OF ENERGY AND ECONOMIC VIABILITY OF THE INTRODUCTION OF INSTALLATIONS FOR NATURAL GAS IN THE RESIDENTIAL AND COMMERCIAL SECTOR |
DISTRIBUTED NON HOMOGENEOUS MODEL FOR FLOW SIMULATION IN FINNED TUBE COIL EVAPORATORS |
DOUBLE DIFFUSIVE NATURAL CONVECTION IN A POROUS CAVITY |
DRYING OF SILKWORM COCOON IN CROSS FLOW BELT CONVEYOR DRYER: A NUMERICAL SIMULATION USING THE FINITE-VOLUME METHOD |
DUAL LAYER SLOT COATING |
EFFECT OF MEDIUM MORPHOLOGY ON LAMINAR FLOW IN A CHANNEL PARTIALLY FILLED WITH A POROUS BED |
EFFECT OF PARAMETERS OF A MULTIGRID METHOD ON THE CPU TIME FOR ONE-DIMENSIONAL PROBLEMS |
EFFECT OF RADIUS OF CURVATURE OF COATING DIE EDGES ON THE PINNING OF STATIC CONTACT LINE |
EFFECTS OF POWER PUMP VARIATIONS IN THE THERMALHYDRAULICS BEHAVIOR OF A TEST SECTION DURING A CRITICAL HEAT FLUX EXPERIMENT |
ELASTOHYDRODYNAMICS OF SLOT COATING PROCESS WITH DEFORMABLE ROLL |
ENERGETIC AND EXERGETIC ANALYSIS OF A THERMAL SYSTEM AIMING COGENERATION |
ENERGETIC AND EXERGETIC ANALYSIS OF A THERMOELECTRIC POWER PLANT |
ENERGETIC, EXERGETIC AND COGENERATON FEASIBILITY ANALYSIS OF A GRANULATED BLAST FURNACE SLAG DRYING SYSTEM |
ESTIMATION OF THE THERMAL DIFFUSIVITY IN SOY GRAINS AT FUNCTION OF GRAINS MOISTURE CONTENT |
EVALUATION OF DIFFERENT TURBULENCE MODELS TO PREDICT A TURBULENT FREE JET |
EVALUATION OF THE WIND POTENTIAL FOR REGIONS OF THE STATE OF ESPIRITO SANTO |
EXACT ANALYTICAL SOLUTION OF STRATIFIED THREE-PHASE LAMINAR FLOW IN A HORIZONTAL RECTANGULAR DUCT |
EXEREGOCONOMIC ANALYSIS IN TWO COGENERATIONS FOR A SHOPPING CENTER IN SALVADOR |
EXERGOCONOMIC ANALYSIS IN TWO COGENERATION PLANTS FOR A SHOPPING CENTER IN SALVADOR |
EXERGOECONOMIC ANALISYS AND EVALUATION OF DIFERENT COGENERATION SYSTEMS |
EXERGOECONOMICS ANALYSIS OF A DOUBLE-EFFECT LITHIUM BROMIDE-WATER ABSORPTION REFRIGERATION SYSTEM |
EXERGY ANALYSIS OF A COGENERATION THERMOELECTRICAL UNITY IN A PETROCHEMICAL COMPLEX |
EXERGY ASSESSMENT OF A COGENERATION SYSTEM WITH MICRO-TURBINE AND ABSORPTION CHILLER |
EXPERIMENTAL ANALYSIS OF THE KINETICS OF TRANSFER AND DECOMPOSITION PROCESSES FOR MODELLING OF FILLING OF RESERVOIRS
|
EXPERIMENTAL AND THEORETICAL EVALUATION OF A SOLAR CHIMNEY TEST PLANT PART I: THEORETICAL TREATMENT |
EXPERIMENTAL AND THEORETICAL EVALUATION OF A SOLAR CHIMNEY TEST PLANT PART II: EXPERIMENTAL RESULTS |
EXPERIMENTAL AND THEORETICAL STUDY OF SLUG LENGTHS IN HORIZONTAL AIR-WATER INTERMITTENT FLOWS |
EXPERIMENTAL DETERMINATION O THE MASS DIFFUSIVITY IN PLASTER PLATES FOR USE IN THE CIVIL CONSTRUCTION |
EXPERIMENTAL DETERMINATION OF TRANSPORT COEFFICIENTS FOR ICE SLURRY IN PLATE HEAT EXCHANGER |
EXPERIMENTAL DRYING OF CERAMIC BRICKS INCLUDING SHRINKAGE |
EXPERIMENTAL INVESTIGATION OF THE TEMPERATURE DISTRIBUTION ON THE TRIGA-IPR-R1 RESEARCH NUCLEAR REACTOR AND DEVELOPMENT OF POWER MEASURING CHANNELS BY THERMAL PROCESSES |
EXPERIMENTAL INVESTIGATION ON LIQUID-LIQUID DISPLACEMENT OF VISCOELASTIC MATERIALS IN CAPILLARY TUBES. |
EXPERIMENTAL PERFORMANCE OTIMIZATION OF A REFRIGERATOR WITH NATURAL GAS AS ITS HEAT SOURCE |
EXPERIMENTAL SIMULATION OF THE FLOW AROUND THE KEEL OF A YACHT |
EXPERIMENTAL STUDY OF A VORTEX TUBE |
FIELD PERFORMANCE TESTING OF TURBOMACHINERY |
FINITE ELEMENT FORMULATION APPLIED TO LINEAR STABILITY ANALYSIS OF VISCOUS FLOWS |
FLOW BEHIND A TWO-DIMENSIONAL BLUNT-TRAILING-EDGED BODY; PART I: OVERALL ANALYSIS. |
FLOW BEHIND A TWO-DIMENSIONAL BLUNT-TRAILING-EDGED BODY; PART II: PHYSICS OF THE WAKE. |
FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS OF A SWIRL JET IMPINGEMENT |
FLUID INTERFACES IN PHASE TRANSITION PROBLEMS: LATTICE-BOLTZMANN METHOD |
FRANCIS HYDRO TURBINE-GENERATOR MODEL FOR MODEL PREDICTIVE SPEED CONTROL |
GALERKIN LEAST-SQUARES MULTI-FIELD APPROXIMATIONS FOR NON-NEWTONIAN FLOWS |
GAS TRANSFER ACROSS GAS-LIQUID BOUNDARIES: PREDICTIONS AND EXPERIMENTS ON CONCENTRATION FLUCTUATIONS |
GENERATION OF THERMAL AND ELECTRIC LOAD PROFILES FOR THE OPTIMIZATION OF A COGENERATION SYSTEM |
GEOGRAPHICAL INFORMATION SYSTEM APPLIED IN TECHNOLOGY DIFFUSION: THE STUDY OF A HIGH POROSITY BRICK |
GRAY RADIATIVE CONDUCTIVE 2D MODELING USING DISCRETE ORDINATES METHOD WITH MULTIDIMENSIONAL SPATIAL SCHEME |
HEAT REMOVAL ENHANCING IN CAPILLARY ELECTROPHORESIS |
HEAT TRANSFER IN SQUARE CAVITIES FILLED WITH CIRCULAR RODS |
HYBRID ANALYTICAL-NUMERICAL SOLUTION TO THE BIOHEAT TRANSFER EQUATION |
HYDRODYNAMIC AND MAGNETIC PAIRWISE INTERACTIONS OF PARTICLES IN A SUSPENSION |
IDENTIFICATION OF TEMPERATURE-DEPENDENT THERMAL PROPERTIES OF SOLID MATERIALS |
IDENTIFICATION OF THERMOPHYSICAL PROPERTIES OF A COMPOSITE ONE-DIMENSIONAL REGION |
IMAGING THE VELOCITY FIELD IN FILM SPLITTING FLOWS OF DILUTE POLYMER SOLUTIONS |
IMPINGING FLOW PARALLEL PLATES HEAT SINKS |
IMPROVED LUMPED PARAMETER FORMULATIONS FOR THE SOLUTION OF CONTAMINANT TRANSPORT PROBLEMS
|
INFLUENCE OF A MOVING WALL CONTOUR IN THE VORTEX STREET OF A CIRCULAR CYLINDER |
INTEGRATION OF A THERMODYNAMIC PROCESS SIMULATOR WITH GENETIC OPERATORS FOR MATHEMATICAL EXERGOECONOMIC OPTIMIZATION OF THERMAL SYSTEMS |
INTEGRATION OF BIGCC BASED-SYSTEMS TO SUGARCANE MILLS |
INTERFACIAL CONVECTIVE HEAT TRANSFER COEFFICIENT FOR LAMINAR FLOW IN POROUS MEDIA |
INVERSE PROBLEM OF SPACE DEPENDENT ALBEDO ESTIMATION WITH ARTIFICIAL NEURAL NETWORKS AND HYBRID METHODS |
INVESTIGATION OF TURBULENT FLOW OVER A STEEP HILL USING LASER DOPPLER ANEMOMETRY |
IRREVERSIBILITY OF THE PHASE CHANGE PROCESS IN DYNAMIC CAVITIES |
LAMINAR FLOW NUMERICAL STUDY USING FINITE ELEMENT METHOD AND CHARACTERISTIC-BASED SPLIT ALGORITHM FOR A SAME PRESSURE AND VELOCITY INTERPOLATION ORDER. |
LARGE EDDY SIMULATION OF AIR FLOW WITHIN A SQUARE ENCLOSURE WITH A PARTIALLY HEATED BOTTOM SURFACE AND COOLED VERTICAL WALLS |
LARGE-EDDY SIMULATION OF THE THREE-DIMENSIONAL UNSTABLE FLOW IN A LID-DRIVEN CAVITY |
LATTICE-BOLTZMANN SIMULATION OF TWO-PHASE FLUID FLOW THROUGH POROUS MEDIA |
LIMITING THERMAL ENERGY RATE INSIDE NUCLEAR FUEL RODS WITH VARIABLES SOURCES |
LOW COST ALTERNATIVE SOLAR COLLECTOR WITH PVC TUBES ABSORPTION SURFACE |
MAGNETOHYDRODYNAMIC OPTIMIZATION OF THE FLUID FLOW DURING THE SOLIDIFICATION OF BINARY MIXTURES IN ENCLOSURES |
MASS TRANSFER SIMULATION OF A FLUIDIZED-BED GASIFIER USING PVC AS RAW MATERIAL |
MASS TRANSFER SIMULATION OF A FLUIDIZED-BED GASIFIER USING SUGAR CANE BAGASSE AS FUEL |
MATHEMATICAL MODELLING AND SIMULATION OF MASS TRANSFER IN HORIZONTAL EXTRACTOR |
METHOD FOR ANALYSING THE COMPOSITION OF THE ELECTRICITY COST GENERATED IN GAS-FIRED COMBINED CYCLE PLANTS |
METHODOLOGY FOR THE OPTIMZATION OF BIOMASS GASIFICATION POWER PLANTS |
METHODOLOGY FOR THERMOGRAPHY APPLICATION IN EVALUATION OF DEFECTS AND NON-APPARENT INCLUSIONS IN MATERIALS |
MIXED CONVECTION EFFECTS IN CAVITIES WITH OSCILLATING BOUNDARIES |
MIXED CONVECTION IN VERTICAL CONCENTRIC CYLINDERS |
MODELING AND SIMULATION OF A SOLAR-POWERED ABSORPTION COOLING SYSTEM LOCATED IN SOUTHEAST BRAZIL |
MODELLING OF WOOD WASTE FUEL CELL/GAS TURBINE FOR SMALL POWER GENERATION |
MOLD FILLING SIMULATION USING A CONTROL VOLUME FINITE ELEMENT METHOD |
MULTIPLE-RELAXATION-TIME LATTICE-BOLTZMANN MODEL FOR IMMISCIBLE FLUIDS |
NATURAL CONVECTION AT ISOTHERMAL VERTICAL PLATE: NEIGHBOURHOOD INFLUENCE |
NATURAL CONVECTION IN AN ARBITRARY INCLINED PLATE WITH PROTRUDING HEATED ELEMENTS. |
NONLINEAR INTERACTIONS BETWEEN WAVE GROUPS AND CURRENTS |
NONLINEAR RESPONSE OF AN OLDROYD FLUID IN STRONG FLOWS |
NUMERICAL ANALYSIS OF IMPURITIES DEPENDENCE OF THE TEMPERATURE FREEZING OF ZINC |
NUMERICAL AND EXPERIMENTAL ANALYSIS OF AXI-SYMMETRIC FLOWS OF VISCOPLASTIC LIQUIDS THROUGH AN EXPANSION FOLLOWED BY A CONTRACTION |
NUMERICAL AND EXPERIMENTAL STUDY OF A HEAT PUMP FOR RESIDENCIAL APPLICATION |
NUMERICAL DETERMINATION OF TRANSVERSE MASS DISPERSION COEFFICIENTS IN POROUS MEDIA |
NUMERICAL EVALUATION OF ANGRA I AUXILIARY FEEDWATER SYSTEM RELIABILITY BY THE METHOD OF SUPLEMENTARY VARIABLES. |
NUMERICAL EVALUATION OF TIME INTEGRATION SCHEMES IN A DISTURBED FLOW SIMULATION |
NUMERICAL INVESTIGATION OF FLUID FLOW IN RADIAL DIFFUSERS WITH IRREGULAR BOUNDARIES |
NUMERICAL INVESTIGATION ON GAS-DISPLACEMENT OF VISCOPLASTIC MATERIALS IN CAPILLARY TUBES |
NUMERICAL MODEL VALIDATION OF ATMOSPHERIC BOUNDARY LAYER OVER COMPLEX TERRAIN |
NUMERICAL MODELING OF A NEWTONIAN AND NON-NEWTONIAN FLUID FLOW IN TUBULAR MEMBRANES APPLIED TO THE MICROFILTRATION AND ULTRAFILTRATION PROCESSES |
NUMERICAL SIMULATION OF 2D FLOW IN CARTRESIAN GEOMETRY USING FINITE VOLUMES |
NUMERICAL SIMULATION OF A CROSS-FLOW HEAT EXCHANGER |
NUMERICAL SIMULATION OF A FLOW OVER A CIRCULAR CYLINDER USING IMMERSED BOUNDARY METHOD IN VORTICITY-VELOCITY FORMULATION |
NUMERICAL SIMULATION OF ADSORPTION COLUMNS: MODEL COMPARISON AND SENSITIVITY ANALYSIS |
NUMERICAL SIMULATION OF AIRFOIL-VORTEX CLOUD INTERACTION IN GROUND EFFECT |
NUMERICAL SIMULATION OF FLOW AND HEAT TRANSFER THROUGH A TUNNEL KILN |
NUMERICAL SIMULATION OF THE FLOW AROUND A SPHERE USING THE IMMERSED BOUNDARY METHOD |
NUMERICAL SIMULATION OF THE FLOW AROUND THE KEEL OF A YACHT |
NUMERICAL SIMULATION OF THE TEMPERATURE AND
CONCENTRATION PROFILES IN A REFRIGERATOR ADSORBER
HEATED BY NATURAL GAS |
NUMERICAL SIMULATION OF THE TURBULENT TRANSITION IN FREE ROUD JETS |
NUMERICAL SIMULATION OF THE TWO-DIMENSIONAL INCOMPRESSIBLE FLOW AROUND AN ELLIPTIC CYLINDER USING THE VORTEX METHOD |
NUMERICAL SIMULATION OF TURBULENT HEAT TRANSFER IN A PIN-FINNED CHANNEL |
NUMERICAL STUDY OF NATURAL CONVECTION IN A PARTIALLY OPEN
ENVIRONMENT WITH A HEAT GENERATING SOURCE |
NUMERICAL STUDY OF THE PULTRUSION PROCESS USING A PARABOLIC APPROACH |
NUMERICAL STUDY OF THE SIMULTANEOUS HEAT AND MASS TRANSFER IN PROLATE SPHEROIDAL BODIES BASED ON THE NONEQUILIBRIUM THERMODYNAMICS |
ON EXERGY DESTRUCTION AND MAXIMUM POWER OUTPUT IN HEAT ENGINES. |
ON THE DYNAMICS OF HUMIDITY ADSORPTION |
ON THE GRID REFINEMENT RATIO FOR ONE-DIMENSIONAL ADVECTIVE PROBLEMS WITH NONUNIFORM GRIDS |
ON THE NUMERICAL CALCULATION OF IMPINGING JETS |
ON THE STABILITY PROBLEM FOR THE FLOW AROUND A 2D CYLINDER BY THE SOLENOIDAL SUB-SPACE PROJECTION METHOD. |
ON THE UNSTEADY MOTION OF AN ISOLATED SEDIMENTING PARTICLE
|
OPTIMIZATION IN THE CO-PROCESSING OF WASTES IN CEMENT INDUSTRY COMPRISING COST, QUALITY AND ENVIRONMENTAL IMPACT |
OPTIMIZATION PROJECT OF THE CONSTRUCTION AND EFFICIENCE ANALYSIS OF A SOLAR COOK FOR FOOD COOKING |
OPTIMIZED DESIGN OF AXIAL-FLOW HYDRAULIC TURBINE |
PARALLEL SIMULATION OF TURBULENT FLOW IN A BACKWARD-FACING STEP |
PASSIVE PROTECTION AGAINST FIRE FOR STRUCTURES AND ELECTRICAL SYSTEMS IN A PETROLEUM REFINING UNIT |
PERFECTIONING OF AN EXPERIMENTAL CHAMBER FOR DETERMINATION OF THERMAL CONDUCTIVITIES |
PERFORMANCE ANALYSIS BETWEEN DIFFERENTS LINEARIZATIONS SCHEMES IN THE DISCRETIZATION OF MOVEMENT EQUATIONS WITH VORONOI DIAGRAMS |
PERFORMANCE ANALYSIS OF TAYLOR-SERIES LINEARIZATION SCHEME OF 1ST ORDER ON THE DISCRETIZATION OF MOVEMENT EQUATIONS WITH VORONOI DIAGRAMS |
PERFORMANCE AND OPTIMISATION OF EXTERNALLY FIRED GAS TURBINES FUELLED WITH BIOMASS |
PERFORMANCE CHARACTERISTICS CURVES FOR GAS LUBRICATED HERRINGBONE GROOVE JOURNAL BEARINGS |
PERFORMANCE EVALUATION OF ADSORPTIVE MATERIALS
FOR DESICCANT COOLING SYSTEMS
|
PERFORMANCE OF GAS TURBINE WITH CARBON DIOXIDE AS THE WORKING FLUID |
PIPE AND CHANNEL FLOW OF MULTIMODE PTT FLUIDS |
POLLUTANT DISPERSION SIMULATION IN THE ATMOSPHERE NEAR SOURCE BY THE GILTT METHOD |
POROSITY EFFECT ON FLOW AND HEAT TRANSFER IN A PARALLEL PLATE CHANNEL WITH POROUS AND SOLID BAFFLES |
PREDICTION OF INTRINSIC PERMEABILITIES WITH LATTICE BOLTZMANN METHOD |
PRELIMINARY STUDY ON THE SPOUTED BED DRYING OF CORK STOPPERS |
PRODUCTION OF HYDROGEN USING HIGH-TEMPERATURE FUEL CELL: ENERGY AND EXERGY ANALYSIS |
RADIATIVE AND CONVECTIVE EFFECTS INSIDE GREENHOUSES |
RADON-222 TRANSPORT INTO OPEN AIR FROM A PHOSPHOGYPSUM STACK: NUMERICAL SIMULATION FOR DIFFERENT ASPECT RATIOS |
RAIN, SUN AND SHADING EFFECTS ON THE THERMODYNAMICS OF SOILS |
REAL TIME SIMULATION OF REGENERATORS WITH FLUID CHANGE OF PHASE FOR ABSORPITON REFRIGERATORS |
REFRIGERANT R134A LEAKAGE THROUGH THE RADIAL CLEARANCE IN ROLLING PISTON COMPRESSORS |
REPRESENTATION OF SOLAR COLLECTORS VIA NEURAL NETWORKS WITH REDUCTION OF THE TRAINING SET NUMBER |
ROTATING DISK FLOW STABILITY IN ELECTROCHEMICAL CELLS: EFFECT OF THE TRANSPORT OF A CHEMICAL SPECIE |
SENSITIVITY ANALYSIS OF A RANKINE CYCLE |
SIMULATION OF A SEMI-CONFINED IMPINGING JET |
SIMULATION OF TURBULENT FLOW IN A SUDDEN CONTRACTION WITH A POROUS INSERT |
SISAL FIBER (AGAVE SISALANA) AS THERMAL INSULATOR OF MANIFOLD |
SOLAR PARABOLIC CYLINDRICAL HEATER WITH FILM OF POLYETHYLENE FOR HEATING OF WATER AND DRYING OF GRAINS |
SPREADING DYNAMICS WITH LATTICE BOLTZMANN METHOD |
STEADY STATE SIMULATION OF DESSULFURIZATION IN CIRCULATING FLUIDIZED BEDS |
STEADY STATE SIMULATION OF HYDRODYNAMICS IN CIRCULATING FLUIDIZED BEDS |
STOCHASTIC APPROACH TO HEAT CONDUCTION PROBLEM USING THE GALERKIN METHOD |
STROUHAL NUMBER FLUCTUATIONS IN A CYLINDER WAKE |
STUDIES ON THE APPLICABILITY OF INFRARED IMAGING OF THERMAL PROCESSES IN TROPICAL REGIONS |
STUDY FOR THE PREDICTION OF STRATIFIED PIPE FLOWS |
STUDY OF A DIFFUSION-ABSORPTION REFRIGERATION CYCLE USING AMMONIA-WATER-HELIUM AS WORKING FLUIDS |
STUDY OF LAMINAR CONVECTIVE HEAT TRANSFER IN HEATED CYLINDERS ROTATING INSIDE OF A RECTANGULAR ENCLOSURE |
STUDY OF LINEAR CASCADE-VORTEX CLOUD INTERACTION |
STUDY OF OPERATION PARAMETERS OF POWER GENERATION SYSTEMS ON SUGAR CANE MILLS |
STUDY OF POWER CAPACITY THROUGH THE AUXILIARY WATER FLOW OF THE IGARAPAVA DAM FISHWAY |
STUDY OF THE APPLICATION OF A NUMERICAL MODEL OF SIMULATION OF THE DRYING PROCESS FOR DIMENSIONING OF ROTARY DRYERS |
STUDY OF THE THERMAL BEHAVIOR OF THE STRUCTURAL HIGH POROSITY BRICK IN BUILDINGS USING THE FINITE ELEMENT METHOD |
STUDY ON HEAT TRANSFER IN TURBULENT FILM FLOW |
SUGAR CANE JUICE EXTRACTION SYSTEMS COMPARISON - MILL
VERSUS DIFFUSER |
SUSTAINABILITY ANALYSIS OF BIODIESEL PRODUCTION CHAIN |
TECHNO-ECONOMIC ASSESSMENT OF VIABILITY OF A PLANT FOR GENERATION OF ELECTRIC ENERGY IN THE AREA OF PARAGOMINAS-PARÁ TROUGHT THE RANKINE CYCLE. |
TEMPERATURE DISTRIBUTION IN A ROTARY HEAT EXCHANGER |
TERMOECONOMIC STUDY OF THE INCREASE IN CAPACITY OF A COGENERATION SYSTEM IN A SUGARCANE ALCOHOL DISTILLERY, ANALYZING THE RESULTS OF THE BAGASSE COMMERCIALIZATION AND OF THE ENERGY |
THE CHALLENGE OF THE PHOTOVOLTAIC SYSTEMS FOR ENERGY SAVINGS |
THE COOLING AND FREEZING OF PARALLELEPIPED FOOD PRODUCT: INFLUENCE OF THE SIZE AND INICIAL MOISTURE CONTENT |
THE DYNAMICAL BEHAVIOR OF A MAGNETIC FLUID FLOW IN A CYLINDRICAL TUBE |
THE EFFECT OF A CELL-DEPLETED LAYER NEAR THE WALL ON THE BLOOD FLOW |
THE EFFECTS OF INTERFERENCE BETWEEN TWO CIRCULAR CYLINDERS ARRANGED IN TANDEM BY VORTEX METHOD |
THE INFLUENCE OF CARBONIZATION TEMPERATURE AND CARBONIZATION HEATING RATE IN THE CHARCOAL PRODUCTION |
THE LOG-LAW METHOD AS A MEANS FOR EVALUATION OF SKIN-FRICTION ON FLOWS OVER ABRUPT CHANGES IN SURFACE ROUGHNESS |
THE USE OF HYDROCARBONS PROPANE AND ISOBUTANE IN REFRIGERATION SYSTEMS |
THEORETICAL ANALYSIS OF AIR CONDITIONING BY EVAPORATIVE COOLING INFLUENCE ON GAS TURBINE CYCLES PERFORMANCE. |
THEORETICAL AND EXPERIMENTAL STUDY OF HEAT DIFFUSION IN STRUCTURES WITH INTERNAL FLAWS |
THEORETICAL STUDY OF A CONCENTRIC TUBES EVAPORATOR OF A REFRIGERATION SYSTEM |
THEORICAL ANALYSIS OF THE CHANNEL FLOW WITH RADIATION IN PARTICIPATING MEDIA THROUGH THE USE OF THE GENERALIZED INTEGRAL TRANSFORM TECHNIQUE |
THEORY AND OCCURRENCE OF EVAPORATION WAVES |
THERMAL EVALUATION OF CONSTRUTIVE MODEL MANUFACTURED IN LIGHTWEIGHT CONCRETE |
THERMAL EXCHANGES IN A BI-FACIALLY IRRADIATED COLLECTOR INTEGRATED TO AN ADSORPTIVE SOLAR REFRIGERATOR |
THERMOECONOMIC APPLICATION FOR COST ALLOCATION IN A DUAL-PURPOSE POWER AND DESALINATION PLANT |
THREE-DIMENSIONAL ANALYSIS OF THE TEMPERATURE AND VELOCITY FIELDS IN CYLINDRICAL THERMAL TANKS |
TRANSIENT THERMAL ANALYSIS OF AN INDUCTION ELECTRIC MOTOR
|
TRANSPORT PHENOMENA IN RAREFIED GASEOUS SYSTEMS |
TURBULENCE MEASUREMENTS IN THE ATMOSPHERIC BOUNDARY LAYER:A COMPARISON BETWEEN HOT-WIRE AND SONIC ANEMOMETER DATA. |
TURBULENT IMPINGING JET IN A CYLINDRICAL ENCLOSURE WITH A POROUS LAYER AT THE BOTTOM |
TWO-DIMENSIONAL NUMERICAL SIMULATION OF FLOWS OVER A VIRTUAL WAVY SURFACE |
TWO-DIMENSIONAL NUMERICAL SIMULATION OF A FREE FALL CYLINDER USING THE IMMERSED BOUNDARY METHOD WITH THE VIRTUAL PHYSICAL MODEL |
UNCERTAINTY ESTIMATE OF THE TEMPERATURE DYNAMIC MEASUREMENT BY SYSTEM IDENTIFICATION METHODS |
UPWIND SCHEMES FOR CONVECTION DOMINATED PROBLEMS |
USE OF SELF-ORGANIZING NEURAL NETWORKS TO IDENTIFY TWOPHASE AIR-WATER FLOW REGIMES IN A HORIZONTAL PIPE |
VELOCITY PROFILE AND TURBULENCE INTENSITY MEASUREMENTS IN THE TA-2 WIND TUNNEL. |
VERIFICATION OF THE DISCRETIZATION ERROR OF NUMERICAL SOLUTIONS OF FLOWS USING UNSTRUCTURED MESHES |
WAVE SLOSHING INSIDE A 2D RESERVOIR |
WAVES ENERGY NEAR THE BAR OF RIO GRANDE`S HARBOR ENTRANCE |
|
top |
|
ENGINEERING EDUCATION |
A GRAPHIC TOOL TO TEACHING AND VISUALIZATION OF THE STRUCTURAL STEEL BEAM DESIGN: LATERALLY UNSUPPORTED |
A HOLISTIC APPROACH TO CONTROL SYSTEMS LABORATORY DESIGN |
A MODEL FOR KNOWLEDGE DOMAIN, PEDAGOGICAL ACTIVITIES, AND TEACHING STRATEGIES REPRESENTATION IN INTELLIGENT TUTORING SYSTEMS APPLIED TO ENGINEERING EDUCATION |
A PARTNERSHIP SCHOOL - INDUSTRY BENEFITING THE INTEGRATION OF THE UNITS OF THE UNIVERSITY
|
AN ENGINEERING COURSE EVALUATION: MEASURING THE STUDENT'S SATISFACTION LEVEL |
BRINGING ENTREPRENEURSHIP INTO MECHANICAL ENGINEERING CURRICULA |
CASE STUDY: NON-LINEAR RESONANT OBJECT CONTROL |
CHALLENGES OF TECHNOLOGICAL EDUCATION IN HISTORY |
CHANGES IN THE CONCEPT OF TECHNOLOGY OF ELEMENTARY SCHOOL TEACHERS AFTER THE TECKIDS PROJECT |
COMPUTER MEETS (DAMIÃO DE) GOIS |
CONSTRUCTION OF A BALL`S MILL: AN EXAMPLE OF INTEGRATION BETWEEN THE BASIC CYCLE AND THE PROFESSIONAL CYCLE IN THE COURSE OF FOOD ENGINEERING OF THE CENTRO UNIVERSITÁRIO DE BELO HORIZONTE |
DIDACTIC GAMES IN ENGINEERING TEACHING - CASE: SPAGHETTI BRIDGES DESIGN AND BUILDING CONTEST |
DIDACTIC TESTS BENCH: PROPOSAL OF INTEGRATION OF UNDERGRAD AND GRADUATE STUDIES IN CEFET/RJ |
DIGITAL CONTROL LABORATORY APPLIED TO TEACHING PURPOSES. |
DISTANCE LEARNING - POTENTIAL AND RISKS IN THE CURRENT SITUATION OF EDUCATION IN BRAZIL
|
EDUCATION NETWORK: PRECISION ENGINEERING. |
EDUCATION OF THE NEW GLOBAL ENGINEER: THE DUAL MASTER DEGREE BETWEEN BRAZIL AND FRANCE. |
ENGINEER' COMPETENCES OR TEACHER' COMPETENCES? |
ENHANCING UNIVERSITY-SCHOOL PARTNERSHIP: A PILOT STUDY |
EVALUATION AND CONTINOUS IMPROVEMENT OF MECHANICAL ENGINEERING PROGRAM USING THE QUALITY FUNCTION DEPLOYMENT TOOL |
FLOW AROUND SPHERES: A DIDACTIC EXPERIMENT |
FRESHMEN AND SENIORS IN ENGINEERING: HOW DO THEY PERCEIVE THE ABILITIES AND COMPETENCES, WHICH ARE IMPORTANT FOR THIS PROFESSION? |
GROUPWARE TOOLS APPLICATION EXPERIMENT IN VIRTUAL ENVIRONMENT |
IMPACT OF THE USE OF AN EDUCATIONAL SOFTWARE FOR STRUCTURAL DYNAMIC ANALYSIS ON THE TEACHING IN THE UNDERGRADUATE ENGINEERING COURSES OF THE FEN/UERJ |
INTELLECTUAL PROPERTY KNOWLEDGE IN MECHANICAL ENGINEERING COURSES |
LEARNING EVALUATION IN TECHNOLOGICAL HIGHER EDUCATION: FROM TRADITION TO NEW PARADIGMS |
MECHATRONICS IN THE DEPARTMENT OF ELECTRICAL ENGINEERING OF THE UNIVERSITY OF PASSO FUNDO |
PATENTS OF COMPUTER SOFTWARES WHEN JOINED IN PRODUCTS OR EQUIPMENT TO IMPROVE THE PRODUCTION SYSTEMS: NEW DRAWING OF THE ENGINEERING TEACHING |
QUALITY IMPROVEMNT OF TEACHING PHYSICS: AN EXPERIENCE ON ENGINIEERING COURSES |
REFORMULATING THE WAY WE TEACH ENGINEERING: A NEW METHODOLOGICAL PROPOSAL |
SOME CONSIDERATIONS ON TESTS, EXAMS AND OTHER STUDENT EVALUATIONS AND ASSESSMENTS |
TEACHING ENGINEERING THERMODYNAMICS TO PROCRASTINATING STUDENTS (AND THE BOLOGNA PROCESS) |
THE BALANCED SCORECARD AS THE GUIDELINE FOR THE MANAGEMENT OF MECHANICAL ENGINEERING COURSES |
THE EXPERIENCE OF VIRTUAL TEAMS |
THE GAME OF KNOWLEDGE: A LUDIC AND EFECTIVE FORM OF CO-CONSTRUCTION OF SIGNIFICANT LEARNING WITHIN THE COLLECTIVITY
OF A UNIVERSITY
|
THE TEACHING OF UNIT OPERATIONS AT MECHANICAL ENGINEERING |
USING SCILAB FOR NONLINEAR DYNAMIC SYSTEMS |
VIRTUAL ENVIRONMENT FOR DYNAMIC MODELING OF MULTI-DOMAIN SYSTEMS
|
VIRTUAL TECHNIQUES APPLIED TO THE EDUCATIONAL PROCESS - AN EXPERIENCE THAT WORKS
|
|
top |
|
MANUFACTURING PROCESSES |
40 HRC PLASTIC MOULD STEELS: MANUFACTURING PROPERTIES CONSIDERATIONS. |
A COMPUTER PROGRAM FOR PREDICTING THERMAL CYCLES AT THE HAZ OF BEAD ON PLATE WELDS USING DIMENSIONS OF THE MOLTEN OR HEAT AFFECTED ZONE AS INPUT DATA |
A FINITE-VOLUME MODEL FOR THE SIMULATION OF THE HOT STRIP ROLLING PROCESS |
A PROCESS PLANNING APPLICATIVE FOR RAPID PROTOTYPING TECHNOLOGY |
A SIMULATION AND PRODUCTION CONTROL ENVIRONMENT THROUGH THE PROCESS MODELLING UTILISING SOFTWARE COMPONENTS |
A SYSTEMATICS TO DEFINE INDUSTRIAL MAINTENANCE MANAGEMENT
|
ACTIVITY-BASED COSTING (ABC) AND THROUGHPUT ACCOUNTING OF TOC (TA): A HYBRID SYSTEM IN THE MANAGERIAL ACCOUNTING |
AGV MODELLING USING OBJECT ORIENTED TECHNIQUES THROUGH UML LANGUAGE IN FMC |
AN ERROR SYNTHESIZATION REDUCED MODEL FOR A CMM |
AN EXPERIMENTAL INVESTIGATION ON THE PERFORMANCE OF GRAPHITE VERSUS COPPER ELECTRODES ON THE FINISH EDM OF TOOL STEEL |
AN EXPERIMENTAL STUDY OF DIE SINKING ELECTRICAL DISCHARGE MACHINING OF AISI D2 TOOL STEEL USING DIFFERENT ELECTRODE MATERIALS |
AN INVESTIGATION ABOUT THE MACHINABILITY OF THE WELD DEPOSITED NICKEL BASED ALLOY INCONEL 625 |
ANALYSING THE VIABILITY OF MANUAL TROLLEY FLEET SUBSTITUTION OF ITEMS RETRIEVING PROCESS |
ANALYSIS OF GG25 GRAY IRON REAMING WITH CEMENTED CARBIDE TOOLS |
ANALYSIS OF THE DYNAMIC STABILITY OF HIGH SPEED FINISHING END MILING AND BALL-END MILLING |
APPLICATION OF DESIGN OF EXPERIMENT METHODOLOGY ON TURNING PARAMETERS OF THE SAE 52100 HARDENED STEEL |
ASPECTS OF PERFORMANCE INFORMATION INTEGRATION IN THE INDUSTRIAL MAINTENANCE |
AUTOMATIC MONITORING AND DIAGNOSIS OF THE DRESSING OPERATION THROUGH THE CLASSIFICATION OF TEXTURAL PATTERNS IN ACOUSTIC MAPS |
AUTOMATIC MONITORING OF POLYMERS FLUX USING IMAGE PROCESSING |
BEAD-ON-PLATE STUDY OF POLYCARBONATE HOT-GAS WELDING |
CHARACTERIZATION OF BURR FORMED ON ENGINE BLOCKS USING METALOGRAPHIC TECHNIQUES |
CHARACTERIZATION OF THE SURFACE GENERATED DURING THE TURNING OF ANNEALED AND AGED AISI 303, 304 AND 310 AUSTENITIC STAINLESS STEEL. |
COMPARATIVE STUDY OF THE DRILLING PROCESS FOR VP 50IM AND DIN 1.2711 MOULD STEELS |
COMPARING DIFFERENT STRATEGIES TO THE MILLING PROCESS OF POCKETS IN DIES WITH INTERCHANGEABLE INSERT MILLS. |
COMPARISON OF TOOL PATH INTERPOLATION ON THE APPLICATION OF THE HSC TECHNOLOGY |
CONSTITUTIVE EQUATIONS FOR AUSTENITIC STAINLESS STEELS HOT DEFORMED AT HIGH STRAIN RATES |
CORRELATING SURFACE ROUGHNESS AND ACOUSTIC EMISSION SIGNALS WITH THE RELATIVE POSITION BETWEEN TOOL AND WORKPIECE DURING CYLINDRICAL TURNING |
DEEP DRILLING IN GG25 GRAY CAST IRON USING TUNGSTEN CARBIDE DRILLS WITH STRAIGHT FLUTES |
DESIGN METHODOLOGY FOR RECONFIGURABLE PRECISION SYSTEMS APPLIED TO AN
ULTRAPRECISION LATHE
|
DESIGN OF PIECES TO BE SUBMITTED TO HEAT TREATMENT: CONCEPTS, PRINCIPLES AND RECOMMENDATIONS. |
DETERMINATION OF THE MECHANICAL BEHAVIOR OF AISI 304 AUSTENITIC STAINLESS STEEL IN MACHINING PROCESSES |
DEVELOPMENT AND ASSESSMENT OF SOFTWARE FOR IMAGE ANALYSES OF COMPOSITE MATERIAL |
DEVELOPMENT AND IMPLAMENTATION OF A METHODOLOGY TO CREATE A TECHNICAL/COMMERCIAL PARTNERSHIP WITH SUPPLIERS |
DEVELOPMENT OF A DEDICATED ROBOTIC SYSTEM FOR STRAIGHTNESS ERROR MEASUREMENT WITH DATA REDUNDANCY |
DEVELOPMENT OF A METHODOLOGY BASED ON A GENERATIVE SYSTEM FOR A CAD/CAPP/CAM SOFTWARE IN MACHINING 2(1/2)D |
DEVELOPMENT OF A NEW WELDED CONSTRUCTION OF INTEGRAL TRUCK TYPE TO RAILWAY FREIGHT CAR TRANSPORT |
DEVELOPMENT OF AN INSTRUMENTED GRIPPER FOR ROBOTIC SHIELDED METAL ARC WELDING |
DIFFUSION BONDING IN STAINLESS STEEL |
DRILLING FORCES OF TI6AL4V WITH MINIMAL QUANTIFY OF LUBRICANT |
DRILLING POLYMERIC MATRIX COMPOSITES REINFORCED WITH GLASS FIBRES |
EFFECT OF MACHINING PARAMETERS ON CUTTING FORCE OF THREE AUSTENITIC STAINLESS STEELS |
EFFECT OF THE MINIATURIZATION IN THE FORMING PROCESS |
EFFECT OF WELDING PARAMETERS ON THE PARTIALLY DILUTED ZONES FORMATION AT DISSIMILAR METAL WELDS |
ELASTIC DEFORMATION ANALYSIS ON GRINDING CYCLES THROUGH VIBRATION SIGNALS |
END MILLING FORCES BEHAVIOR STUDY BY SIMULATION AND FINITE ELEMENTS DINAMIC ANALISYS |
ENGINE DESIGN USING RAPID PROTOTYPING TECHNIQUES |
EVALUATION OF INFLUENCE OF CONTINUOUS ANNEALING PROCESS AND BATCH HEATING IN THE DRAWABILITY OF INTERSTITIAL FREE STEEL |
EVALUATION OF MACHINED SURFACE ROUGHNESS THROUGH ACOUSTIC EMISSION |
EVALUATION OF THE MACHINABILITY OF TI-6AL-4V ALLOY WITH (SICW) WHISKER REINFORCED ALUMINA CERAMIC CUTTING TOOL UNDER VARIOUS COOLING ENVIRONMENTS |
EVALUATION OF THE PERFORMANCE OF COATED HSS DRILLS IN MACHINING OF AL-SI ALLOYS |
EXTENDED VALUE STREAM MAPPING APPLIED IN AUTOMOBILE INDUSTRY TO DESIGN A LEAN SUPPLY CHAIN |
FINITE ELEMENT SIMULATION OF TIG WELDING: STRUCTURAL ANALYSIS |
FINITE ELEMENT SIMULATION OF TIG WELDING: THERMAL ANALYSIS |
FUZZY MODELING OF TOOL WEAR IN DRILLING |
HIGH PRESSURE PHASE TRANSFORMATION IN SINGLE CRYSTAL SILICON DURING DUCTILE REGIME DIAMOND TURNING |
HIGH SPEED IMAGES OF RESISTANCE SPOT WELDING SYNCHRONIZED WITH ELECTRICAL SIGNALS |
HIGH TEMPERATURE BRAZING OF INCONEL AND STAINLESS STEEL COMPONENTS FOR A SATELLITE THRUSTER PROPULSION |
IDENTIFICATION AND CONTROL OF METAL TRANSFER IN PULSED GMAW |
IMAGE PROCESSING APPLIED TO THE CNC PROGRAMMING IN DRILLING PROCESS. |
INCREASE OF THE PRODUCTIVE CAPACITY DUE TO THE SETUP REDUCTION: CASE STUDY IN THE INDUSTRY OF MEDICAL PRODUCTS |
INCREASING TOOL LIFE IN GRINDING THROUGH CUTTING FLUID SUPPLY WITH SHOE NOZZLES |
INFLUENCE OF THE LUBRI-COOLING SYSTEM ON THE LIFE OF TIALN COATED HSS TWIST DRILLS WHEN MACHINING BLIND AND THROUG HOLES |
INFLUENCE OF THE SHIELDING GAS COMPOSITION ON THE MORPHOLOGY AND ARC STABILITY IN GMA WELDING OF THE ASTM A516 STEEL |
INFLUENCE OF TOOL OVERHANG ON TOOL WEAR IN HARDENED STEEL MILLING |
INTELLIGENT AUTOMATIC IDENTIFICATION OF PROBLEMS IN PRACTICAL APPLICATIONS OF TURNING |
INTERNAL SIGNAL FROM AN OPEN ARCHITECTURE CNC APPLIED TO THE CUTTING TOOL WEAR MONITORING: IMPLEMENTATION AND VALIDATION |
MANUFACTURE SYSTEM OF COMPLEX PRODUCTS |
MODELING AND IMPLEMENTATION OF A FLEXIBLE MANUFACTURING CELL (FMC) |
MODELING AND SIMULATION OF CUTTING TOOL EDGE ERRORS ON PRECISION MILLING
|
MONITORING OF THE DRILLING PROCESS IN DUPLEX STAINLESS STEEL |
NEAR DRY MACHINING (NDM) BY DROPPING IN TURNING OF STAINLESS STEELS |
NEURAL NETWORK FOR CONSTANT FORCE CONTROL OF END MILLING |
NUMERICAL MODEL FOR FLATNESS ANALYSIS OF THIN STEEL SHEET IN TENSION LEVELLING PROCESS |
OPTIMISATION OF CUTTING TOOLS USING CA-TECHNOLOGIES |
OPTIMISATION OF EDM FAST HOLE-DRILLING THROUGH EVALUATION OF DIELECTRIC AND ELECTRODE MATERIALS |
OPTIMIZATION OF A MULTI-RESPONSE GMAW-P PROCESS BY DESIGN OF EXPERIMENTS AND PRINCIPAL COMPONENT ANALYSIS |
PARAMETRIC AND NEURAL METHODS FOR COST ESTIMATION OF PROCESS VESSELS |
PERFORMANCE EVALUATION OF CUTTING TOOLS PRODUCED BY BRAZING OF A CVD DIAMOND FILM ON A WC-CO SUBSTRATE |
PERFORMANCE OF COOLING/LUBRICATION CONDITIONS IN THE ROUGH MILLING OF THE 15-5 PH STAINLESS STEEL |
PINCH EFFECT OBSERVATION IN MIG/MAG WELDING OF AWS ER 309L WIRE |
PROFILE CHARACTERIZATION OF THE PRODUCT DEVELOPMENT STRATEGIES IN THE SMALL AND MEDIUM ENTERPRISES OF THE METAL-MECHANICS SECTOR. |
RECONFIGURABLE ULTRAPRECISION LATHE QUALITY EVALUATION THROUGH
COMPARISON BETWEEN ITS MACHINED PARTS AGAINST A REFERENCE
|
REPAIR WELDING OF INJECTION MOLDS MANUFACTURED IN AISI P20 AND VP50IM STEELS |
RESIDUAL STRESS ON STAINLESS STEEL A304 TUBE DRAWN WITH FIXED PLUG |
SIMULATION OF THE MANUFACTURING PROCESS OF SEAMLESS TUBES AT V&M DO BRASIL |
SIMULTANEOUS 5-AXES AND 3-AXES MILLING COMPARISON APPLIED ON A AUTOMOTIVE COMPONENT |
SOME EFFECTS OF STOCK VARIATIONS DUE TO THE USE OF 2½ AXES STRATEGY ON ROUGHNING |
STUDY OF SHORT-TERM MACHINABILITY TESTS FOR THE SAE 12L14 FREE-CUTTING STEEL |
TAPPING OPERATION AT HIGH CUTTING SPEED |
TECHNICAL AND ECONOMIC EVALUATION OF AN INSTALLATION PROJECT OF A PILOT PLANT IN THE TECHNICAL ASSISTANCE LABORATORY OF A CERAMIC GLAZE PRODUCER |
THE BENEFITS THAT THE VISUAL MANAGEMENT CAN BRING FOR THE COMPANIES |
THE EFFECT OF CYCLIC BENDING ON THE MECHANICAL PROPERTIES OF DRAWN STEEL BARS |
THE INFLUENCE OF SOME CUTTING PARAMETERS IN FINISHING MILLING OF HARDENED STEEL USING A BALL NOSE TOOL |
THE INFLUENCE OF THE FRICTION FACTOR ON THE TOTAL FORMING FORCE IN "T" METALLIC JUNCTIONS EMPLOYING ELASTOMERS |
THE LEAN MANUFACTURING SYSTEM AND ITS CONTRIBUTIONS TO THE STRATEGY OF A MANUFACTURING COMPANY. |
THE NEED FOR NEW PARADIGMS FOR INDICATORS OF INOVATION IN COMPANIES |
TOOL WEAR IN HIGH SPEED MILLING OF HARDENED STEEL |
TOPOGRAPHIC FUNCTIONAL PARAMETERS IN MACHINING OF AISI 4340 STEEL WITH COATED CEMENTED CARBIDE TOOLS |
ULTRAPRECISION LATHE QUALITY IMPROVEMENT THROUGH EFFECT ANALYSIS
|
USE OF METHODS BASED ON TIME SERIES FOR IMPROVEMENT OF
THE ACCURACY OF THE DEMAND FORECAST IN A PARTS
DISTRIBUTION CENTER: A CASE STUDY |
WAVELET PACKET FEATURE EXTRACTION FOR VIBRATION MONITORING IN HIGH SPEED MILLING |
WEAR RESISTANCE OF GREY CAST IRON |
WIRE ELECTRICAL DISCHARGE MACHINING OF THIN TI6AL4V PLATES: ROUGH MACHINING ASSESSMENT |
|
top |
|
MATERIALS SCIENCE AND ENGINEERING |
3-D CONSTRAINT EFFECTS ON FRACTURE MECHANICS SPECIMENS |
A DAMAGE INTERFACE MODEL FOR ADHESIVE BONDED JOINTS |
A METHOD TO OPTIMIZE CERAMIC MASSES FOR COATINGS USING THE LOSS FUNCTION |
A MODEL OF FRACTIONAL FACTORIAL DESIGN OF EXPERIMENTS IN AIRCRAFT COMPONENTS ENGINE |
A NEW BOUNDARY CONDITION FOR THE EVALUATION OF HYDROGEN TRANSPORT IN METALS USING AN ELECTROCHEMICAL TECHNIQUE |
A STUDY ON HYDROGEN INDUCED CRACKING IN API STEEL WELD METAL USING THE MODIFIED G-BOP TEST |
A SURVEY ON CERAMIC COMPOSITES FOR APPLICATION IN POROUS BEARINGS |
A TWO-STAGE TRANSFORMATION IN CU-ZN-AL SMA WIRES |
AGING STUDY IN A CU-AL-MN SHAPE MEMORY ALLOY |
AN EXPERIMENTAL ANALYSIS OF SANDWICH COMPOSITES WITH FUNCTIONALLY GRADED CORE UNDER TRANSVERSE LOADING |
ANALYSE OF THE INJECTION PARAMETER IN IMPACT PROPERTIES OF THE POLYPROPYLENE - PP
|
ANALYSIS ON THE PERFORMANCE OF MECHANICAL TEST LABORATORIES BASED ON A PROFICIENCY TESTING |
APPLICABILITY OF THE HIGH VELOCITY COMBUSTION WIRE (HVCW) SPRAYING PROCESS FOR THE DEPOSITION OF PROTECTIVE METALLIC COATINGS |
APPLICATION OF LASER DOPPLER VIBROMETRY FOR STRUCTURAL DIAGNOSTICS ON COMPOSITE PANELS : NEW EXAMPLES |
ASPECTS RELATED TO THE GRAIN SIZE OF IRON SAMPLES SINTERED IN HOLLOW CATHODE DISCHARGE |
ASSESSMENT OF FATIGUE PROPERTIES AND S-N CURVES FOR DIN EN 10283 ALLOY STEEL
|
BEHAVIOUR OF SI CONTAINING DLC FILMS IN INTERNAL COMBUSTION ENGINE COMPONENTS |
BENDING MOMENT DISTRIBUTION OF INTERNALLY PRESSURIZED REPAIRED PIPES |
BENDING RESISTANCE OF COMPOSITE STEEL-CONCRETE BEAMS IN FIRE SITUATION |
BIOCOMPATIBILITY OF TI-13ZR-13NB AND PASSIVATED 316L STAINLESS STEEL COATED WITH TICN |
CHARACTERIZATION OF CERAMIC COMPOSITES DERIVED FROM POLYSILOXANE/NB/AL/AL2O3 BY AFCOP PROCESS |
CHARACTERIZATION OF LIGHTWEIGHT MORTARS FOR STAINLESS STEEL SINK APPLICATIONS |
CHARACTERIZATION OF THE MAGNETIC NOISE BARKHAUSEN USING WAVELETS TRANSFORM |
CLASSIFICATION OF PULSE-ECHO AND TOFD ULTRA-SONIC SIGNALS USING ARTIFICIAL NEURAL NETWORK |
COMPARATIVE STUDY OF TOUGHNESS AND WEAR RESISTANCE OF HIGH SPEED STEELS PM SINTER 23 AND CONVENTIONAL AISI M2 |
COMPOSITE TUBES AT LOWER FURNACE OF KRAFT PULPING PROCESS CHEMICAL RECOVERY BOILER-MATERIAL AND CRACKING PROCESS ANALYSIS |
COMPUTER SIMULATION OF HIGH-TEMPERATURE CORROSION PHENOMENA |
CONSTITUTIVE MODELING OF STRESS-STRAIN CURVE OF HOT DEFORMED IF AUSTENITE |
CORROSION CHARACTERISTICS OF COATING TYPE 309L STAINLESS STEEL PREPARED BY WELD OVERLAY |
CROSS-FLOW MICROFILTRATION WITH MICROPOROUS TUBES CHEMICALLY TREATED FOR DESEMULSIFYING MIXTURES OF WATER AND SUNFLOWER OIL |
DAMAGE ASSESSMENT OF AISI 8620 STEEL SUBMITTED TO AXIAL FATIGUE |
DAMAGE IN STEEL BARS APPLIED FOR CIVIL CONSTRUCTION SUBMITTED TO CORROSION |
DETERMINATION OF THE ACOUSTIC PROPERTIES OF TUNGSTEN/EPOXY AND TUNGSTEN/POLYURETHANE COMPOSITES USING ULTRASONIC TRANSMISSION TECHNIQUE |
DETERMINATION OF THE EXPERIMENTAL PARAMETERS RELATED TO THE PRIMARY AND SECONDARY CREEP STAGES OF THE TI-6AL-4V ALLOY WITH ATMOSPHERE CONTROLING |
DETERMINATION OF THE STRESS DISTRIBUTION FUNCTION BY X-RAY DIFFRACTION USING FOURIER ANALYSIS |
DEVELOPMENT OF AN ESTER VINYL POLYMERIC MATRIX FOR COMPOSITES DESIGNED FOR THE FILAMENT WINDING PROCESS AND EFFECT OF WATER ABSORPTION ON MECHANICAL PROPERTIES |
DEVELOPMENT OF PLASTIC ETA FACTORS FOR DEEP AND SHALLOW CRACKED BEND SPECIMENS EMPLOYED IN J-R CURVE TESTING |
DEVELOPMENT OF THERMAL FATIGUE TESTING APPARATUS |
DIAMOND-LIKE CARBON DEPOSITION BY A TRIODE PECVD |
DIAMOND-LIKE CARBON FILMS DEPOSITED BY A TRIODE PECVD UNDER TWO LEVELS OF ACETYLENE FLOW RATE |
DISCONTINUITIES EVALUATION ON SUBMERGED WET WELDS |
ECOGENIC RESPONSE AND DOSIMETRIC EVALUATION OF HYDROXYAPATITE MACROAGGREGATES IMPLANTS |
EFFECT OF COPPER ADDITION ON DELAYED CRACKING PHENOMENON OF DEEP-DRAWN AND REDRAWN CUPS OF AUSTENITIC STAINLESS STEELS |
EFFECT OF GRAIN REFINING AND HOMOGENIZING TREATMENT ON AL-FE-MN-SI CAST ALLOYS |
EFFECT OF HOLLOW CATHODE DISCHARGE PARAMETERS ON THE OXIDATION OF PLASMA-TREATED TITANIUM SURFACES |
EFFECT OF INITIAL SURFACE ROUGHNESS ON WEAR MECHANISMS OF CONTACT FATIGUE - TESTS WITH AUSTEMPERED DUCTILE IRON |
EFFECT OF PRESTRAIN AND BAKE HARDENING HEAT TREATMENT ON THE FATIGUE CRACK GROWTH AND CRACK CLOSURE OF TWO DUAL-PHASE STEELS |
EFFECT OF THE MICROSTRUCTURE AND THICKNESS OF NITRIDED CASES ON THE ABRASIVE WEAR RESISTANCE OF DUPLEX LAYERED TIN-PVD COATINGS |
EFFECT OF WATER AGING IN MECHANICAL PROPERTIES OF COMPOSITE
MATERIAL FOR FILAMENT WINDING |
EFFECT OF WATER AND OIL ON THE STRENGTH OF COMPOSITES MATERIALS |
EFFECTS OF CORROSION ON THE DAMAGE AND FAILURE OF CONCRETE |
ESTUDY OF THE GAS ATMOSPHERE IN PLASMA NITRIDING OF STEEL AISI H13 |
EVALUATION OF DYNAMIC FRACTURE MECHANICS IN AN AISI 316 STAINLESS STEEL USING INSTRUMENTED CHARPY IMPACT TESTING |
EVALUATION OF THE PVC DEGRADATION USED IN BUILDING. MECHANICAL PROPERTIES |
EXACT SOLUTION OF THE SPTT MODEL FOR FULLY DEVELOPED CHANNEL FLOWS |
EXPERIMENT OF RECYCLING AND USE OF SOLID WASTES ON BRICKS PRODUTION TO CIVIL ENGINEERING (BRICKWORK). |
EXPERIMENTAL ANALYSIS OF THE PERFORMANCE OF COMPOSITE
MATERIAL USED AS CRACK FATIGUE REPAIR
|
EXPERIMENTAL AND NUMERICAL ANALYSIS FOR SE(B) AND SE(T)
J-INTEGRAL FRACTURE TOUGHNESS TESTING
|
EXPERIMENTAL TECHNIQUE FOR CREEP CRACK GROWTH RATE MEASUREMENT IN A LOW CARBON STEEL |
EXPERIMENTAL, NUMERICAL AND ANALYTICAL ANALYSIS OF THE FORCE DURING IF STEEL CUP DEEP DRAWING. |
FATIGUE BEHAVIOR OF API GRADE 5L X-65 AND X-70 STEELS WELDED JOINTS UNDER VARIABLE AMPLITUDE LOADING. |
FATIGUE BEHAVIOR OF FERRITIC STAINLESS STEELS
USED IN EXHAUST SYSTEMS
|
FATIGUE CRACK PROPAGATION RATES OF THE ALUMINIUM ALLOY |
FATIGUE FAILURE OF CENTRIFUGAL BOMB AXIS |
FATIGUE LIFE MODELING FOR INDUSTRIAL COMPOSITES MATERIALS |
FEM STUDY OF THE CONTACT AREA AND PRYING ACTION IN T-STUB STEEL CONNECTION |
FORMATION OF WEAR DEBRIS IN POLYMERIC TRIBOSYSTEMS |
FRACTURE PROPERTIES OF FIBER REINFORCED POLYMER CONCRETE UNDER MARINE ENVIRONMENT EXPOSURE |
FRICTION AND WEAR OF AL-SI/SICP COMPOSITES IN RECIPROCATING SLIDING AGAINST AISI 52100 STEEL |
GAS PRESSURE SINTERIZATION OF SILICON NITRIDE BASED CERAMICS USING RARE EARTH OXIDES AS SINTERING ADDITIVES |
GRAIN SIZE MEASUREMENT BY IMAGE ANALYSIS: AN APPLICATION IN THE CERAMIC AND IN THE METALLIC INDUSTRIES |
HARD, WEAR RESISTANT COATINGS DEPOSITED ON SINTERED TOOL MATERIALS. |
HEXAMETILDISSILOXANE PLASMA DEPOSITION ON AL2O3 CERAMICS: WATERPROOFING EFFECT |
HYBRID COMPOSITES WITH SYNTHETIC AND NATURAL FIBERS: DEGRADATION BY MOISTURE ABSORPTION |
IMPACT AND BALLISTIC EVALUATION OF POLYCARBONATE PROTECTORS FOR GLASS INSULATORS IN TRANSMISSION LINES |
INFLUENCE OF COPPER CONTENT ON WORKABILITY OF COLD ROLLED AL-MG-CU ALLOYS |
INFLUENCE OF INJECTION PARAMETER IN THE POLYPROPYLENE DIMENSIONS AND MASS |
INFLUENCE OF NITRIDING TIME ON THE MICROHARDNESS PROFILE OF PLASMA NITRITED AISI D6 STEEL |
INFLUENCE OF PROCESSING PARAMETERS ON STRUCTURAL AND MAGNETIC PROPERTIES OF THE GD5.09GE2.03SI1.88 COMPOUND |
INFLUENCE OF THE MATERIALS MECHANICAL PROPERTIES ON THE STRUCTURAL INTEGRITY ASSESSMENT OF CRACKED PIPING OF PWR NUCLEAR REACTORS PRIMARY SYSTEMS |
INFLUENCE OF THE SUBMERGED ARC WELDING IN THE MECHANICAL BEHAVIOUR OF THE P355NL1 STEEL. PART I: ANALYSIS OF THE CYCLIC ELASTOPLASTIC BEHAVIOUR |
INFLUENCE OF THE SUBMERGED ARC WELDING IN THE MECHANICAL BEHAVIOUR OF THE P355NL1 STEEL. PART II: ANALYSIS OF THE LOW/HIGH CYCLE FATIGUE BEHAVIOURS |
INSTRUMENTED CHARPY IMPACT TEST: OPERATIONAL TIME REDUCTION FOR ACQUISITION AND PLOTING OF THE LOAD - TIME CURVE |
INVESTIGATION OF THE INCORPORATION OF ZIRCONIUM INTO THE HYDROXYAPATITE STRUCTURE OF ZIRCONIA-HYDROXYAPATITE COMPOSITES AND ZIRCONIUM HYDROXYAPATITE POWDERS. |
J-INTEGRAL VERSUS CTOD δ5 FRACTURE TOUGHNESS OF UNIDIRECTIONAL FIBER-METAL LAMINATES |
LASER SURFACE TREATMENT OF SPHEROIDAL GRAPHITE CAST STEEL |
LAY-UP EVALUATION IN COMPOSITE MATERIAL TUBES |
MATRIX CONSOLIDATION MECHANISM IN THE TI/SIC/C COMPOSITES PRODUCED BY CONTINUOUS BINDER-POWDER COATING |
MEASUREMENT OF SENSITIZED STRUCTURES OBTAINED BY BRIEF TIME THERMAL TREATMENT IN AUSTENITIC STAINLESS STEEL. |
MECHANICAL CHARACTERIZATION OF TIO2 CERAMICS CONTAINING AL2O3 AND SIO2. |
MECHANICAL PROPERTIES OF FIBERGLASS PRESSURE PIPES WITH SILICEOUS SAND FILLER |
METHODOLOGIES FOR LOAD DISTRIBUTION ON A KAPLAN HYDRO TURBINE BLADE |
METHODOLOGY FOR DETERMINATION OF THE OPTIMUM DIE ANGLE IN WIRE DRAWING |
MICROHARDNESS EVALUATION OF A DIRECT/INDIRECT HYBRID COMPOSITE RESIN AT COMPLEMENTARY ACTIVATION IN LIGHT OR HEAT |
MICROSTRUCTURAL ANALYSIS OF STAINLESS STEEL CLADDING
DEPOSITED WITH PULSED CURRENT AND CONVENTIONAL
CONTINUOUS CURRENT GMAW PROCESSES |
MICROSTRUCTURAL CHARACTERIZATION OF TI-20NB ALLOY FOR ORTHOPEDIC IMPLANTS |
MICROSTRUCTURE OF TI-CU AND TI-NB CAST ALLOYS FOR MEDICAL AND DENTAL IMPLANTS |
MODELING FLOW CURVES OF HLSA AND IF STEEL IN THE AUSTENITE |
MODELLING OF SOLIDIFICATION OF ATOMISED DROPLETS |
NIOBIUM CAVITATION ANALYSIS BY SEM |
NON-LINEAR BURGERS´ EQUATION SOLUTION FOR TWO DIMENSIONAL LID-DRIVEN CAVITY |
NUMERICAL SIMULATION OF PITTING CORROSION |
NUMERICAL SIMULATION OF VISCOELASTIC FREE SURFACE FLOWS USING THE SECOND ORDER FLUID CONSTITUTIVE EQUATION |
OBTAINING AND CHARACTERIZATION OF BETA TITANIUM ALLOY FOR MEDICAL APPLICATIONS |
ON THE EXPERIMENTAL REALISATION OF MULTI-AXIAL STRESS STATES FOR CELLULAR AND POROUS MATERIALS: DETERMINATION OF ELASTO-PLASTIC PROPERTIES |
OPTICAL PROPERTIES OF FLEXIBLE ORGANIC LIGHT EMITTING DIODES UNDER MECHANICAL STRAIN |
OVERHEATING INFLUENCE IN THE SOLIDIFICATION PARAMETERS AND MICROSTRUCTURE FORMATION OF ALUMINUM 5052 ALLOY |
PARALLEL SOLUTION ON A PC CLUSTER AND BEHAVIOR ANALYSIS OF BI AND THREE-DIMENSIONAL STRUCTURAL PROBLEMS UTILIZING THE FINITE ELEMENT METHOD |
PREDICTION MODELS OF MICRO-SCALE ABRASION OF THIN COATED SURFACES |
PROCESSING OF AN ULTRAFINE GRAINED C-MN STEEL AND ITS CORRELATION WITH MECHANICAL BEHAVIOR
|
PROPOSAL OF AN AUTOMATIC SYSTEM OF INCORPORATION OF WATER IN THE PRODUCTION OF PIECES OF RED CERAMIC |
REMOVING MATERIAL NOISE IN EDDY-CURRENT INSPECTIONS OF STEAM GENERATORS TUBES USING WAVELET TRANSFORM |
RESIDUAL STRESS EVALUATION OF AA2024-T3 FRICTION STIR WELDED JOINTS |
RHEOLOGICAL BEHAVIOR OF DENSE GRANULAR MEDIA |
SELECTION OF MATERIALS FOR CUT TOOLS OF MOTORIZED MANUAL WEEDER FOIL |
SEM/EDS ANALYSIS OF MICROSTRUCTURE OF DENTAL RESTORATIVE SYSTEMS: INFLUENCE ON OPTICAL DENSITY |
SHOT PEENING ON THE FATIGUE STRENGTH OF AL7050-T7451 COATED BY HVOF |
SILICON NITRIDE CERAMICS OBTANING FOR ALTERNATIVE SINTERING ADDITIVE |
SLOT MACHINING EFFECTS ON RESIDUAL STRESS MEASUREMENTS USING THE CRACK COMPLIANCE METHOD |
SOLID PARTICLE EROSIOIN IN SUPERALLOY INCONEL 600 |
SOLIDIFICATION OF UNDERCOOLED AL-FE-ND ALLOY |
STRAIN AGING IN AISI 304 STAINLESS STEEL |
STRESS DISTRIBUTION DURING CAVITATION OF COMPACT GRAPHITE IRON |
STRESSES AND DISPLACEMENTS ANALYSES ON LAMINATED COMPOSITES IN UNMANNED AERIAL VEHICLE WINGS |
STUDY OF CARBON FILMS DEPOSITION BY PECVD WITH SI INCORPORATION BY VACCUM EVAPORATION |
STUDY OF EFFECTS FROM THE ADDITION OF POLYMER ON THE COMPRESSION RESISTANCE IN BULK APPLIED IN THE CERAMIC INDUSTRY. |
STUDY OF PRECIPITATION HARDENING DURING THE AGING AND OVERAGING IN MARAGING CLASS 300 STEEL |
STUDY OF SPINODAL DECOMPOSITION OF A DUPLEX STAINLESS STEEL BY NON-DESTRUCTIVE TEST |
STUDY OF THE INTERFACE MATRIX-INCLUSION PROPERTIES
ON FRACTURE PROPERTIES IN COMPOSITE MATERIALS |
STUDY OF THE THERMAL STRESS IN CERAMIC MATERIALS DURING COOLING
|
SUPERPLASTIC BEHAVIOR OF A FE-MN-AL AUSTENITIC STAINLESS STEEL |
SURFACE MODIFICATION OF TI6AL4V ALLOY BY DUPLEX PLASMA PROCESSING |
THE EFFECT OF CYCLIC TORSION ON THE DRAWING STRESS OF 304 STAINLESS STEEL AND 6063 ALUMINUM ALLOY BARS |
THE EFFECTS OF IMPURITIES CARBON AND OXYGEN ON THE TEMPERATURES AND ENTHALPIES OF MARTENSITIC TRANSFORMATION OF NITI SMA |
THE INFLUENCE OF SURFACE TREATMENT ON THE MOISTURE ABSORPTION OF COCONUT SHELL FIBER |
THE INFLUENCE OF TERNARY COATING (TI-C-N) ON SURFACE FINISH OF AISI 4340 AND AA 6262-T6 ALUMINUM AFTER TURNING
|
THE INFLUENCE OF THE ADDITION OF NATURAL GYPSUM ON THE MICROSTRUCTURE OF THE SET PLASTER: STUDY OF THE MECHANICAL AND MICROSTRUCTURE PROPERTIES |
THE NEW COMPETITIVE ENVIRONMENT REQUIRES A NEW APPROACH FOR THE ORGANIZATIONAL COMPETENCES |
THE PERFORMANCE OF NEW GEAR OIL CONTAINING MOLYBDENUM DISULFIDE |
THE USE OF ACOUSTIC EMISSION IN THE CHARACTERIZATION OF STEEL PIPELINE DAMAGE |
THE USE OF MAGNETIC BARKHAUSEN NOISE ANALYSIS FOR MECHANICAL STRESSES EVALUATION |
THERMAL AND MECHANICAL PROPERTIES ANALYSES OF SISAL FIBER COMPOSITES |
THERMAL STRESSES IN THE INTERFACE OF AL2O3/TIO2 CERAMIC LAYERS |
THERMODYNAMIC CONSISTENT VERSION OF THE GRIFFITH FRACTURE CRITERION |
THERMODYNAMIC STUDY OF SIMPLIFIED SBF SOLUTIONS |
TI-6AL-4V MACHINING WITH SILICON NITRIDE CUTTING TOOLS: A SCIENTIFIC AND TECHNOLOGICAL CONTRIBUTION |
ULTRASONIC IMMERSION TECHNIQUES FOR THE MEASUREMENT OF ELASTIC CONSTANTS IN FIBER-REINFORCED COMPOSITES. |
WATER SORPTION IN UNSATURATED POLYESTER COMPOSITES REINFORCED WITH JUTE AND JUTE/GLASS FIBER FABRICS: MODELLING AND SIMULATION |
WEAR MODE TRANSITION DURING THE MICRO-SCALE ABRASION OF WC-CO P20 AND M2 TOOL STEEL |
|
top |
|
MECHATRONICS |
3-D MEASUREMENT FROM IMAGES USING A RANGE BOX |
A CARRIAGE POSITIONING CONTROL SYSTEM USING A CNC OPEN ARCHITECTURE FOR ACADEMIC PURPOSES |
A COMPUTER VISION SYSTEM BASED ON MULTI-LAYER PERCEPTRONS FOR CONTROLLING MOBILE ROBOTS |
A CONTROL AND AUTOMATION SYSTEM FOR MEDICINE PREPARATION USING RECONFIGURABLE ARCHITECTURES |
A DESCRIPTION OF A VERY LOW COST UNDERWATER VEHICLE PROJECT |
A DIGITAL SYSTEM FOR MEASUREMENTS IN GYPSUM MOLDS FOR ORTHODONTICS |
A DISPLACEMENT ESTIMATOR FOR MAGNETIC BEARINGS |
A FLEXIBLE DIGITAL PID CONTROLLER FOR AN INTERNAL COMBUSTION ENGINE TESTING SYSTEM |
A MASTER-SLAVE ROBOT FOR TELEMANIPULATION WITH HAPTIC FEEDBACK |
A NEW FAMILY OF 3-DOF PARALLEL ROBOT MANIPULATORS FOR PICK-AND PLACE OPERATIONS |
A NEW PROCEDURE FOR ROBUST CONTROL DESIGN OF COOLING MACHINES BASED ON VAPOR COMPRESSSION |
A PETRI NET BASED PLATFORM FOR DISTRIBUTED MODELING AND SIMULATION OF PRODUCTIVE SYSTEMS |
A REVIEW OF MODELING AND SIMULATION OF AUTONOMOUS MOBILE ROBOTS AIDED BY SIMULATION SOFTWARE AND PETRI NETS |
A STUDY ON A PROGRESSIVE WAVE TYPE NOVEL PIEZOELECTRIC PUMP |
ACOUSTIC TRANSMISSION WITH MODE CONVERSION PHENOMENON |
ADAPTIVE CASCADE CONTROL OF A HYDRAULIC ACTUATOR WITH AN ADAPTIVE DEAD-ZONE COMPENSATION |
AN ADAPTIVE FAILURE DETECTION APPROACH FOR REAL-TIME DISTRIBUTED CONTROL SYSTEMS OVER SHARED ETHERNET |
AN OPTIMIZED VISUAL TRACKING SYSTEM APPLIED TO ROBOT NAVIGATION |
ANALYSIS OF EXTREMES, OVERSHOOT AND UNDERSHOOT IN THE LINEAR CONTROL CONTINUOUS-TIME SYSTEM OF THIRD ORDER WITH REAL ZEROS AND POLES |
APPLYING THE SIMULATED ANNEALING TO THE PROBLEM OF POSITIONING ROTATIONAL NON CONVEX POLYGONS |
ASPECTS OF FABRICATION AND CHARACTERIZATION OF ELECTRO-THERMAL MICRO ACTUATORS |
BACTERIA COLONY APPROACHES WITH VARIABLE VELOCITY APPLIED TO PATH OPTIMIZATION OF MOBILE ROBOTS |
COMPARATIVE ANALYSIS OF METHODS FOR REDUNDANCY SOLUTION OF UNDERWATER VEHICLE-MANIPULATOR SYSTEMS |
COMPARISON OF CONTROL STRATEGIES FOR MOTORIZATION OF A SERVO ASSISTED WHEELCHAIR |
COMPARISON OF INTELLIGENT TECHNIQUES FOR A CASE STUDY IN CONTROL SYSTEMS |
COMPOSITION, COORDINATION AND SIMULATION OF REACTIVE FUZZY BEHAVIORS FOR AN MOBILE AGRICULTURAL ROBOT |
CONCATENATION OF THE MOVEMENTS OF THE MANIPULATOR AND THE CAMERA OF THE ROV |
CONTROL OF MOBILE ROBOTS VIA INTERNET |
CONVERGENCE AND DISCRETIZATION CHARACTERISTICS OF A STAGGERED ALGORITHM FOR MICROELECTROMECHANICAL SYSTEMS SIMULATION. |
COOPERATIVE AUTONOMOUS UNMANNED AERIAL VEHICLES FOR DATA COMMUNICATION AND FOR MONITORING UNSTRUCTURED ENVIRONMENTS |
DESIGN AND SIMULATION OF A PIEZORESISTIVE PRESSURE MICROSENSOR |
DESIGN OF ELECTROTHERMOMECHANICAL MEMS |
DESIGN OF HIGH PRECISION POSITIONING AND MEASURING MACHINES USING VIRTUAL PROTOTYPING. |
DEVELOPMENT AND APLICATION OF A VISION SYSTEM FOR INDUSTRIAL ROBOT |
DEVELOPMENT OF A CLOSED-LOOP CONTROLLER FOR FILE TEETH MANUFACTURE USING AN INDUSTRIAL MACHINE |
DEVELOPMENT OF A MAGNETICALLY BORNE ELECTRICAL MOTOR PROTOTYPE |
DEVELOPMENT OF A SYSTEM INTERNET-BASED COLLABORATIVE CAD/CAPP/CAM IN A CONTEXT OF E-MANUFACTURING |
DEVELOPMENT OF AN AUTOMATIC INSPECTION EQUIPMENT BASED ON THE TOFD TECHNIQUE. |
DEVELOPMENT OF AN ELECTROTHERMOMECHANICAL XY MICROPOSITIONER |
DEVELOPMENT OF AN OPEN DISTRIBUTED APPROACH FOR BUILDING AUTOMATION |
DIRECT SINGULARITY AVOIDANCE STRATEGY FOR THE HEXA PARALLEL ROBOT |
DISCUSSING ACCURACY IN AN AUTOMATIC MEASUREMENT SYSTEM USING COMPUTER VISION TECHNIQUES |
DYNAMIC MODELING OF A HIGH SPEED TROLLEY FOR TV TRANSMISSION |
DYNAMICS AND JACOBIAN ANALYSIS OF A PARALLEL ARCHITECTURE ROBOT: THE HEXA |
ELECTRICAL ACTIVATION UNDER CONSTANT LOAD OF TI-NI AND CU-ZN-AL SMA WIRE ACTUATORS |
EXPERIMENTAL AND NUMERICAL CHARACTERIZATION OF PIEZOELECTRIC
MECHANISMS DESIGNED USING TOPOLOGY OPTIMIZATION |
FAULT IDENTIFICATION IN FUEL CELLS BASED ON BAYESIAN NETWORK DIAGNOSIS |
FINITE ELEMENT ANALYSIS OF AN ELECTROMAGNETIC ACTUATOR |
FORMAL COMPREHENSIVENESS AND UNIFORMITY AND SEMANTIC INTRA AND INTERMODEL CONSISTENCY IN THE REPRESENTATION OF DISCRETE EVENT DYNAMIC SYSTEM MODELS |
FUZZY INSTRUMENTAL VARIABLE ALGORITHM FOR ONLINE MULTIVARIABLE NEURAL IDENTIFICATION |
GUN-TURRET MODELLING AND CONTROL |
HARDWARE RECONFIGURABLE CONTROL WITH OPENED ARCHITECTURE FOR MOBILE ROBOTS |
HIGH-PRECISION SLITS BASED ON A MONOLITHIC WEAK-LINK MECHANISM |
HOW TO ASSIGN TIME-OPTIMAL TRAJECTORIES TO PARALLEL ROBOTS - AN ADAPTIVE JERK-LIMITED APPROACH |
HYBRID DELIBERATIVE/REACTIVE ARCHITECTURE FOR HUMAN-ROBOT INTERACTION |
IBEX - A FRAMEWORK FOR HARDWARE IN THE LOOP SIMULATION |
IMPACT CONTROL DURING THE CONTACT TRANSITION OF A FLEXIBLE LINK MANIPULATOR |
IMPLEMENTATION OF 3D SHAPE RECONSTRUCTION FROM RANGE IMAGES FOR OBJECT DIGITAL MODELING |
INSTRUMENTATION ARCHITECTURE AND REAL-TIME CONTROL OF MICROTURBINE |
INTELLIGENT GAIN-SCHEDULING CONTROL FOR MULTIVARIABLE DISCRETE LINEAR TIME VARYING SYSTEMS. |
INTERDIGITATED-TYPE MICROSENSOR TO MEASURE SOLUTION CONCENTRATION |
INVERSE KINEMATICS OF A BINARY FLEXIBLE MANIPULATOR USING GENETIC ALGORITHMS |
KINEMATIC ANALYSIS OF A FOUR LEGGEG ROBOT SUSPENDED ON WIRE |
KINEMATIC CONTROL OF MOBILE ROBOTS TO PRODUCE CHAOTIC TRAJECTORIES
|
KINEMATICS AND WORKSPACE ANALYSIS OF A PARALLEL ARCHITECTURE ROBOT: THE HEXA |
LEARNING BASED REGRASPING APPLIED TO AN ANTROPOMORPHIC ROBOT HAND |
LEARNING BAYESIAN NETWORKS FOR FAULT DETECTION: APPLICATION TO THE 747 LONGITUDINAL MOTION |
LEARNING OF B-SPLINE NEURAL NETWORK USING
NEW PARTICLE SWARM APPROACHES
|
LINE BALANCING WITH GENETIC ALGORITHMS |
LOW-COST PWM DRIVE FOR AN ELECTRIC MINI-BAJA TYPE VEHICLE |
MANAGEMENT AND COLLECTING DATA IN THE INFORMED MANUFACTURING |
MEMS SENSOR APPLICATION FOR THE MOTION ANALYSIS IN SPORTS SCIENCE |
MIDDLEWARE ARCHITECTURES IN EMBEDDED SYSTEMS APPLICATION |
MIXED REALITY WITH HYPER-BONDS FOR MECHATRONICS DESIGN |
MOBILE ROBOT LOCALIZATION AND MAPPING USING SPACE INVARIANT TRANSFORMS |
MOBILE ROBOT PATH CONTROL USING LANDMARK INFORMATION |
MODELING OF A CONTROL ARCHITECTURE FOR A MINI-ROBOT NAVIGATION USING PETRI NETS |
MODELING OF DISTRIBUTED COLLABORATIVE CONTROL SYSTEMS OF PRODUCTION SYSTEMS |
MODELING OF FIRE PROTECTION SYSTEMS IN INTELLIGENT BUILDINGS |
MOTION STRUCTURE ANALYSIS AND ERROR QUANTIFICATION - AN EPIPOLAR GEOMETRY BASED APPROACH |
MULTIPLE CHANNEL ACTIVE NOISE CONTROL |
MULTIPLE MOBILE ROBOTS IN A COOPERATING STRUCTURE
|
MULTIVARIABLE H_2 AND H_INFINITY CONTROL FOR WIND ENERGY CONVERSION SYSTEM - A COMPARISON |
MULTIVARIABLE PREDICTIVE CONTROL WITH CONSTRAINS OF REFRIGERATION SYSTEMS |
NAVIGATION SYSTEM OF AUTONOMOUS MOBILE ROBOT USING OMNIDIRECTIONAL VISION AND FUZZY CONTROLLER |
NEW METHODOGY FOR INDENTIFICATION OF THE DEAD ZONE IN PROPORTIONAL DIRECTIONAL HYDRAULIC VALVES |
NUMERICAL ANALYSIS AND EXPERIMENTAL STUDY BY MICRO LASER DOPPLER VIBROMETER FOR THE DYNAMIC CHARACTERIZATION OF RF MEMS SWITCHES |
NUMERICAL ANALYSIS OF A HIGH POWER PIEZOELECTRIC TRANSDUCER USED IN THE CUTTING AND WELDING OF THERMOPLASTIC TEXTILES |
NUMERICAL AND EXPERIMENTAL ANALYSIS FOR MICROFLUIDIC DEVICES MANUFACTURED IN LTCC |
NUMERICAL MODELING OF A CIRCULAR PIEZOELECTRIC ULTRASONIC TRANSDUCER RADIATING IN WATER |
OBSTACLE AVOIDANCE PROCEDURE FOR MOBILE ROBOTS |
OMNIDIRECTIONAL STEREOVISION SYSTEM WITH TWO-LOBE HYPERBOLIC MIRROR FOR ROBOT NAVIGATION |
OPTIMIZED DESIGN OF AN ELECTROSTATIC SIDE-DRIVE MICROMOTOR |
OPTIMIZED PERFORMANCE OF A MOTOR-BEARING |
OUT-OF-PLANE MOTION MICROACTUATORS MADE OF THIN FILM METALLIC GLASS |
PATH PLANNING FOR MOBILE ROBOTS OPERATING IN OUTDOOR ENVIRONMENTS USING MAP OVERLAY AND TRIANGULAR DECOMPOSITION |
PATH PLANNING OF ROBOT WELDING TRAJECTORIES USING SCREW
THEORY |
PHOTOELASTIC FRINGE PATTERN ANALYSIS BY IMAGE PROCESSING |
PREDICTIVE CONTROL APPLIED TO ROBOTICS JOINTS USING FPGA |
PREDICTIVE CONTROL OF A MAGNETIC LEVITATION SYSTEM WITH EXPLICIT TREATMENT OF OPERATIONAL CONSTRAINTS |
PROCESS MODELING AND FAULT DIAGNOSIS OF FLEXIBLE ASSEMBLY SYSTEMS USING PETRI NET |
PROJECT OF CONTROL OF THE OPEN CNC
IN AGILE MANUFACTURING SYSTEM
|
PROPOSAL OF A SENSOR MONITORING SYSTEM FOR A MECHATRONIC ORTHOPAEDIC SAW |
QUALITY ESTIMATION USING GENERIC MODEL PARAMETERS AND NEURAL NETWORK |
REAL TIME ACTION PLAN SYNTHESIS AND EXECUTION IN INTELLIGENT MANUFACTURING SYSTEMS |
RELIABILITY OF ELECTRO-HYDRAULIC EQUIPMENT: SYSTEMATIZATION AND ANALYSIS |
REMOTE SUPERVISION OF A DIDACTIC INTEGRATED MANUFACTURING PLANT |
ROBOT MANIPULATOR JOINT CONTROL WITH NEURO-FUZZY FRICTION COMPENSATION |
ROUGH-TERRAIN ROBOT MOTION PLANNING BASED ON
TOPOLOGY AND TERRAIN CONSTITUTION |
SCANNING MIRRORS AS TUNNING DEVICE IN OSCILLATOR SYSTEMS. |
SIMULATION OF ULTRASONIC FIELDS GENERATED BY SINGLE AND ARRAY TRANSDUCERS THROUGH INTERFACES |
SOFTWARE ARCHITECTURE FOR AUTONOMOUS VEHICLES |
SPECIFICATION AND ANALYSIS FOR AUTOMATED FLEXIBLE MANUFACTURING |
STIFFNESS IMPROVEMENT OF A 1 - D.O.F CONTROLLED MAGNETIC LINEAR BEARING |
STUDY OF INFRARED SENSING AS WELD PENETRATION TIG PROCESS |
STUDY OF THE FRICTION BEHAVIOR IN INDUSTRIAL PNEUMATIC ACTUATORS |
THE INFORMATION SYSTEMS AND MANUFACTURING PROCESSES INTEGRATION: SURVEY AND FUTURE TRENDS |
THRUSTER DYNAMICS COMPENSATION FOR THE POSITIONING OF UNDERWATER ROBOTIC VEHICLES THROUGH A FUZZY SLIDING MODE BASED APPROACH |
TOOL PATH GENERATION FOR FREE-FORM SURFACES MACHINING IN CNC MACHINE-TOOLS |
TREND OF PRECISION POSITIONING TECHNOLOGY |
UNCERTAINTY IN HYBRID SYSTEMS AND ITS APPLICATION TO AIRCRAFT SYSTEMS |
UNIDIMENSIONAL MODELING AND CONSTRUCTION OF A 1-3 PIEZOELECTRIC COMPOSITE TRANSDUCER |
USING MONITORING SYSTEMS IN MACHINE-TOOLS FOR REDUCTION OF SET-UP TIME |
VARIABLE STRUCTURE CASCADE CONTROL OF A PNEUMATIC POSITIONING SYSTEM
|
VISUAL ROBOTIC TRACKING SYSTEM USING A TEMPLATE MATCHING ALGORITHM |
WAVELET ANALYSIS AND ARTIFICIAL NEURAL NETWORKS APPLIED TO CONDITION MONITORING IN HIGH SPEED MILLING |
|
top |
|
OFFSHORE & PETROLEUM ENGINEERING |
A GANTRY TYPE SEMI-PASSIVE ARM TO SUPPORT AUV`S OFFSHORE ACTIVITIES |
A GIS-BASED ENVIRONMENTAL MANAGEMENT SYSTEM FOR OIL AND GAS INDUSTRY |
A METHOD FOR MEASUREMENT OF HYDRAULIC LOSSES IN CENTRIFUGAL PUMPS
|
A METHODOLOGY FOR OPTIMIZATION OF PRODUCTION STRATEGY FOR DEVELOPED OIL FIELDS |
A NOTICEABLE QUESTION OF THE WATER ENTRY PROBLEM: THE SPLIT OF KINETIC ENERGY DURING THE INITIAL STAGE |
A RISKS QUANTIFICATION PROCEDURE BASED ON BAYESIAN INFERENCE |
ACTIVE CONTROL OF COUPLED AXIAL AND TORSIONAL DRILL-STRING VIBRATIONS |
ADHESIVENESS STUDY OF POLIMERYC MATRIX COMPOSITE MATERIAL FOR PIPELINES REPAIR |
AN INTELLIGENT SYSTEM FOR AUTOMATED CLASSIFICATION DRILLING REPORT |
AN INVERTED FLOW PATTERN DEPENDENT MODEL FOR HORIZONTAL AND INCLINED OIL-WATER WELL LOGGING |
ANALYSIS OF OFFLOADING OPERATIONS IN FPSO UNITS |
ANALYSIS OF SEVERAL SOFTWARES USED IN PETROLEUM RESERVOIR SIMULATION |
APPLICATION OF ULTRASONIC TECHNIQUE IN CORE FLOW MONITORING AND CONTROL |
ASSESSMENT OF STRESS CONCENTRATION ON DENTED PIPELINES |
AUTOMATED CLASSIFICATION SYSTEM FOR PETROLEUM WELL DRILLING USING MUD-LOGGING DATA |
CALCULATION OF THE DRAG OF A SHIP HULL USING RANS |
CHARACTERIZATION OF FLUIDS AND POROUS MEDIA TO STUDY FLOW PROCESS |
CONTROLLED SHORT-CIRCUITING MIG/MAG WELDING (CCC) APPLIED TO THE ROOT PASS IN THE CONSTRUCTION OF OFFSHORE OIL PIPELINES - PROCESS ANALYSIS TOOLS |
DESCRIPTION OF A VERTICAL RISER BEHAVIOR IN FREQUENCY AND TIME DOMAIN |
DESIGN AND CONTROL OF PIG OPERATIONS THROUGH PIPELINES |
DESIGN OF ELASTIC BASES FOR VIV EXPERIMENTS |
DESIGN, ASSEMBLING AND VERIFICATION OF A CIRCULATING WATER CHANNEL FACILITY FOR FLUID DYNAMICS EXPERIMENTS |
DEVELOPMENT OF A SIX-COMPONENT BALANCE FOR MEASUREMENTS OF FORCES AND MOMENTS ACTING IN IMMERSED CYLINDERS |
DEVELOPMENT OF PARTICLE METHOD REPRESENTING FLOATING
BODIES WITH HIGHLY NON-LINEAR WAVES |
DISCUSSION OF INDUSTRIAL PIPING VIBRATION FAILURE CRITERIA |
DYNAMIC ANALYSIS OF LAZY-WAVE STEEL RISERS |
ECONOMICAL ANALYSIS OF PETROLEUM FIELDS UNDER SOLUTION GAS DRIVE. |
EFFECT OF STEEL CASING SURFACE CONDITIONS ON THE ADHERENCE OF OILWELL CEMENTS |
EFFECT OF WATER INJECTION UNDER FRACTURING CONDITIONS ON THE DEVELOPMENT OF PETROLEUM RESERVOIRS |
EVALUATION OF A TOP TENSIONED RISER MODEL FOR EXPERIMENTS |
EXPERIMENTAL CREEP ANALYSIS ON HMPE SYNTHETIC FIBER ROPES FOR OFFSHORE MOORING SYSTEMS |
EXPERIMENTAL VALIDATION OF MODELS FOR PREDICTING WAX REMOVAL FORCES IN PIGGING OPERATIONS |
FATIGUE ANALYSIS OF LAZY-WAVE STEEL RISERS |
FATIGUE LIFE ASSESSMENT OF REELED RISERS |
FLOW OF WATER-IN-OIL EMULSIONS - FIELD RESULTS VS. NUMERICAL PREDICTIONS |
FLOW VISUALIZATION OF EMULSIONS THROUGH A PORE-THROAT CAPILLARY MODEL |
FRICTIONAL AND ACCELERATING PRESSURE DROPS EFFECTS ON HORIZONTAL OIL WELL PRODUCTIVITY INDEX |
GAS TURBINE SELECTION IN COGENERATION SYSTEM APPLIED IN OFFSHORE PLATFORMS. |
GENERATION OF PETROLEUM COKE IN THE REFINE OF HEAVY OILS AND ITS USE IN ROTARY KILNS OF CLINKER PRODUCION |
HYBRID KNOWLEDGE BASED SYSTEM: A DECISION-SUPPORT PROPOSAL FOR NATURAL GAS COMPRESSOR STATION MAINTENANCE AND OPERATION |
HYDRODYNAMIC PARAMETER ESTIMATION OF AN UNMANNED UNDERWATER VEHICLE |
IMPLEMENTATION OF CORNER POINT MESH INTO A PARALLEL, FULLY IMPLICIT, EQUATION OF STATE COMPOSITIONAL RESERVOIR SIMULATOR |
INFLUENCE OF THE VIBRATION ON THE ABSOLUTE PERMEABILITY OF POROUS MEDIA SATURATED WITH WATER |
LEAK DETECTION IN GAS PIPELINES - A KNOWLEDGE BASED APPROACH |
METAL-COMPOSITE PIPES FOR DEEPWATER APPLICATIONS |
METHODOLOGY FOR GENERATING QUALITY MAPS WITH APPLICATION IN THE SELECTION AND OPTIMIZATION OF DRAINAGE STRATEGIES OF OIL RESERVOIRS |
MODEL TEST UTILIZATION FOR THE DEVELOPMENT OF THE FIRST FULL SCALE RISER SUPPORT BUOY (BSR) |
MODELING AND EXPERIMENTAL EVALUATION OF THE FACTORS AFFECTING DRILLING FLUID INVASION THROUGH RESERVOIR ROCKS |
NON-INTRUSIVE CAPACITIVE PROBE FOR MEASUREMENT OF IN-SITU VOLUMETRIC FRACTION IN WATER-OIL AND WATER-AIR FLOWS |
NUMERICAL STUDY OF A SELF STANDING RISER SYSTEM |
PARAMETRIC ANALYSIS OF STEEL LAZY-WAVE RISERS |
PORTFOLIO OPTIMIZATION OF OIL PRODUCTION PROJECTS USING MATHEMATICAL PROGRAMMING AND UTILITY THEORY |
PRESSURE DROP AND RE-START TIME DURING STOP-AND-GO EXPERIMENTS IN CORE-ANNULAR FLOW |
PROPOSAL OF A MATHEMATICAL MODEL OF FOULING IN DISTILLATION PROCESS. |
PWD ANALYSIS IN DEEPWATER ENVIRONMENTS: CAMPOS BASIN CASE STUDIES |
RECOVERY MECHANISMS OF FOAMY OIL |
RECOVERY STRATEGIES FOR NATURALLY FRACTURED RESERVOIRS. A RESERVOIR SIMULATION APPROACH |
SIMULATION OF A SOLIDS FREE DRILL-IN FLUID INVASION THROUGH OIL RESERVOIR ROCKS |
SIMULATION OF HORIZONTAL AND VERTICAL THERMAL GRADIENT IN PETROLEUM RESERVOIR |
SIMULATION OF HORIZONTAL TWO-PHASE SLUG FLOWS USING THE TWO-FLUID MODEL WITH A CONSERVATIVE AND NONCONSERVATIVE FORMULATION |
STATIC ANALYSIS OF LAZY-WAVE STEEL RISERS |
THE EFFECTS OF STIFFENERS MODELED BY SHELL ELEMENTS IN A FPSO 3D FEM HULL ANALYSIS |
THE INFLUENCE OF PRODUCTION SYSTEM CONSTRAINTS ON THE RESERVOIR STRATEGY OPTIMIZATION |
THE INFLUENCE OF THE PARAMETER SPACE AND THE OBJECTIVE FUNCTIONS DEFINITION IN THE HISTORY MATCHING |
THE STUDY OF WELL PLANNING USING THE KICK TOLERANCE CONCEPT |
THREE-DIMENSIONAL NONLINEAR THEORY OFWATER IMPACT |
TIME-FREQUENCY ANALYSIS OF INTERMITTENT TWO-PHASE FLOWS IN HORIZONTAL PIPING |
TRANSIENT THERMAL ANALYSIS IN SUBSEA PIPELINES |
ULTRASONIC GUIDED WAVE INSPECTION IN RIGID RISER |
VALUE OF INFORMATION DURING APPRAISAL AND DEVELOPMENT OF PETROLEUM FIELDS |
WAX DEPOSITION IN LAMINAR CHANNEL FLOW |
|
top |
|