Symposia Topics
MAN03 - Machining
COBEM2007-1987
DRILLING FIBRE REINFORCED PLASTIC: A NOVEL DELAMINATION FACTOR
Alexandre Mendes Abrão, Antônio Esteves Correia, J. Paulo Davim, Juan C. Campos Rubio, Paulo Eustáquio Faria,
COBEM2007-1941
AN ANALYTICAL MODEL FOR TOOL WEAR USING THE SLIP-LINE FIELD APPROACH
Jose Luis L. Silveira, Lucio Fabio Cassiano Nascimento,
COBEM2007-1703
OPTIMIZATION OF FINISHING FACE MILLING OF GRAY CAST IRON IRREGULAR SURFACES WITH CERAMIC TOOLS
Anselmo Eduardo Diniz, Jorge Antonio Giles Ferrer,
COBEM2007-1661
STUDY OF SURFACE FINISH OF ALUMINUM ALLOYS IN TURNING WITH COATED CERAMIC CUTTING TOOLS
Alexandre Carlos Eduardo, Jalon de Morais Vieira, José Reinaldo de Oliveira Júnior, Renato Françoso de Avila,
COBEM2007-1662
DIMENSIONAL CONTROL IN ALUMINUM WORKPIECE MACHINED WITH COATED CERAMIC CUTTING TOOLS
Jalon de Morais Vieira, José Reinaldo de Oliveira Júnior, Paulo Rogério Araújo Guimarães, Renato Françoso de Ávila,
COBEM2007-1444
THE TOOL WEAR AND TOOL LIFE OF HSS TIN COATED HELICAL DRILL IN MACHINING TESTS OF ABNT 304 AND VILLARES 304 UF STAINLESS STEEL.
Davi Neves, Jorge Antonio Giles Ferrer, Olívio Novaski, Robson de Camargo,
COBEM2007-1452
THE COMPARATIVE ANALYSIS OF MACHINABILITY OF ABNT 304 AND VILLARES 304 UF WITH HSS HELICAL DRILL.
Davi Neves, Jorge Antonio Giles Ferrer, Olívio Novaski, Robson de Camargo,
COBEM2007-1464
INFLUENCE OF THE SENSOR POSITION IN THE SIGNAL OF ACOUSTIC EMISSION WHEN MONITORING MILLING OPERATION
Andre Luis Beloni Dos Santos, Marcio Bacci Da Silva, Rodrigo Henriques Lopes Da Silva, Ulisses Borges Souto,
COBEM2007-1519
A CONTRIBUTION TO THE STUDY OF TI-6AL-4V TURNING
Elias Alves da Cunha, Fernando Cesar Yokio Cursino Sato, Marcos Roberto Vargas Moreira, Marcos Valério Ribeiro,
COBEM2007-1294
PARAMETRIC EVALUATION OF CYLINDRICAL MAGNETIC ABRASIVE FINISHING PROCESS
Flávio J. Lorini, Heraldo J. Amorim, Matheus S. Gomes,
COBEM2007-1303
INFLUENCE OF TYPE OF CUTTING FLUID IN DRILLING OF ALUMINUM ALLOY
Aleksander Schoeffel, Flávio Deminicis, Ricardo Pimentel, Salete Martins Alves,
COBEM2007-1330
THE DIFFERENCES IN FEED FORCE AND TORQUE IN DRILLING TWO SIMILAR AUSTENITIC STAINLESS STEEL.
Davi Neves, Jorge Antonio Giles Ferrer, Olívio Novaski, Robson de Camargo,
COBEM2007-0964
ANALYSIS OF BEHAVIOR OF WEAR IN CUTTING TOOLS ON TURNING OF AUSTEMPERED DUCTILE IRON.
Cássio Luiz Francisco de Andrade, Marcelo Teixeira dos Santos, Paulo André de Camargo Beltrão, Valter Vander de Oliveira,
COBEM2007-0995
STRESS ANALYSIS OF THE MACHINING PROCESS THROUGH THE FINITE ELEMENT METHOD (FEM): THE EFFECT OF A SINGLE MNS INCLUSION.
Diego Fernando González Santos, Izabel Fernanda Machado, Pablo Alejandro Correa Saldarriaga, Roberto Martins Souza,
COBEM2007-1020
EVALUATION OF THE ACOUSTIC EMISSION MONITORING TECHNIQUE IN TURNING OF TI-6AL-4V ALLOY WITH HIGH-PRESSURE COOLANT SUPPLY
Bonney John, Emmanuel Okechukwu Ezugwu, Wisley Falco Sales,
COBEM2007-0854
EVALUATION OF NANO-GRAIN SIZE CERAMICS WHEN MACHINING TI-6AL-4V ALLOY UNDER CONVENTIONAL COOLANT FLOW
Álisson Rocha Machado, Éder Silva Costa, Emmanuel O. Ezugwu, John Bonney, Rosemar Batista Da Silva,
COBEM2007-0726
SURFACE TEXTURE IN FINAL MILLING OF INCLINED HARDENED STEEL
Frank Patrick Missell, Gerson Luiz Nicola, Rodrigo Panosso Zeilmann,
COBEM2007-0739
ESTIMATE OF FORCES IN THE TURNING PROCESS USING VIBRATION MONITORING.
Márcio da Silva Bacci, Marcus Antonio Viana Duarte, Tatiana Meola,
COBEM2007-0740
DRILLING OF HARDENED STEEL WITH MINIMAL QUANTITY OF LUBRICANT
Andréia Vanessa Finimundi, Diego Carlos Calza, Rodrigo Panosso Zeilmann,
COBEM2007-0601
CUTTING TOOL GEOMETRY SUGGESTIONS BASED ON A FUZZY LOGIC MODEL
Carlos Julio Cortés Rodríguez, José Manuel Arroyo Osorio, Oscar Germán Duarte Velasco,
COBEM2007-0445
WC-CO COATED CARBIDE SUBSTRATE SURFACE TEXTURING WITH A PULSED CUHBR LASER
Anselmo Eduardo Diniz, José Manuel Arroyo Osorio, Milton Sergio Fernandes de Lima,
COBEM2007-0456
HARD TURNING OF INTERRUPTED SURFACES USING PCBN AND CERAMIC TOOLS
Adilson Jodé Oliveira, Anselmo Eduardo Diniz, Daniel Cirillo Marques, Davi Janini Ursolino,
COBEM2007-0486
DRILL-THREADING PROCESS PERFORMANCE WHEN MACHINING AISI AL-SI-CU4 ALLOY: DYNAMIC BEHAVIOUR ANALYSES USING MATHEMATICAL AND EXPERIMENTAL METHODS
Gomes Gurgel Alexandre, Landre Júnior Jánes, Marcelo Becker, Wisley Falco Sales,
COBEM2007-0506
MILLING OF ANNEALED AND HARDENED TOOL STEEL WITH COATED CARBIDE AND CERMET INSERTS
Alexandre Mendes Abrão, José Luiz Silva Ribeiro,
COBEM2007-0381
STUDY OF THE PLASMA NITRIDED LAYER HOMOGENEITY IN CYLINDRICAL HOLES OF LOW-CARBON STEEL SAMPLES
Silvio Francisco Brunatto, Valdair José Pimentel,
COBEM2007-0358
INFLUENCE OF THE CUTTING FLUID CONDITIONS IN FINISHING MILLING OF 15-5PH STAINLESS STEEL
Aldo Braghini Júnior, Anselmo Eduardo Diniz, Fernando Teixeira Filho,
COBEM2007-0363
EXPERIMENTAL STUDIES OF MECHANICAL BEHAVIOR OF FDM RAPID PROTOTYPED PARTS
Alan Eduardo Lam, Anderson Vicente Borille, Jefferson de Oliveira Gomes,
COBEM2007-0167
OPTIMIZATION OF THE CUTTING CONDITIONS (VC, FZ AND DOC) FOR BURR MINIMIZATION IN FACE MILLING OF DIE STEEL
Álisson Rocha Machado, Jefferson Duarte Silva, José Renato de Freitas Oliveira, Sezimaria de Fátima Pereira Saramago,
COBEM2007-0181
PERFORMANCE OF THE VEGETABLE OIL BASED EMULSION WHEN DRILLING 15-5 PH MARTENSITIC STAINLESS STEEL GRADE
Aldo Braghini Junior, Anselmo Eduardo Diniz, Armando Ítalo Sette Antonialli,
COBEM2007-0027
PROCESS PARAMETERS FOR FINISH EDM OF AISI H13 TOOL STEEL WITH COPPER-TUNGSTEN ELECTRODES
COBEM2007-0028
ASSESSMENT OF COPPER-TUNGSTEN ELECTRODE EDGE RADIUS WEAR FOR EDM OF AISI H13 TOOL STEEL
